 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| EN29PL064/032 EN29PL064/032 64/32 Mbit (4/2 M x 16-Bit) CMOS 3.0 Volt- only, Simultaneous-Read/Write Flash Memory Distinctive Characteristics Architectural Advantages * 64/32 Mbit Page Mode devices - Page size of 4 words: Fast page read access from random locations within the page * Single power supply operation - Voltage range of 2.7V to 3.3V valid for MCP product - Single Voltage, 2.7V to 3.6V for Read and Write operations * Simultaneous Read/Write Operation - Data can be continuously read from one bank while executing erase/ program functions in another bank - Zero latency switching from write to read operations * FlexBank Architecture( PL064/PL032) - 4 separate banks, with up to two simultaneous operations per device - Bank A: PL064 - 8 Mbit (4 Kw x 8 and 32 Kw x 15) PL032 - 4 Mbit (4 Kw x 8 and 32 Kw x 7) - Bank B: PL064 - 24 Mbit (32 Kw x 48) PL032 - 12 Mbit (32 Kw x 24) - Bank C: PL064 - 24 Mbit (32 Kw x 48) PL032 - 12 Mbit (32 Kw x 24) - Bank D: PL064 - 8 Mbit (4 Kw x 8 and 32 Kw x 15) PL032 - 4 Mbit (4 Kw x 8 and 32 Kw x 7) * Secured Silicon Sector region - Up to 64 customer-lockable words * Both top and bottom boot blocks in one device * Data Retention: 20 years typical * Cycling Endurance: 100K cycles per sector typical Performance Characteristics * * High Performance Page access times as fast as 25 ns Random access times as fast as 70 ns 32-word/64-byte write buffer reduces overall programming time for multiple-word updates Power consumption (typical values at 10 MHz) 45 mA active read current 17 mA program/erase current 0.2 A typical standby mode current Software Features * Software command-set compatible with JEDEC 42.4 standard * CFI (Common Flash Interface) compliant - Provides device-specific information to the system, allowing host software to easily reconfigure for different Flash devices * Erase Suspend / Erase Resume - Suspends an erase operation to allow read or program operations in other sectors of same bank * Program Suspend / Program Resume - Suspends a program operation to allow read operation from sectors other than the one being programmed * Unlock Bypass Program command - Reduces overall programming time when issuing multiple program command sequences Hardware Features * Ready/Busy# pin (RY/BY#) - Provides a hardware method of detecting program or erase cycle completion * Hardware reset pin (RESET#) - Hardware method to reset the device to reading array data * WP#/ ACC (Write Protect/Acceleration) input - At VIL, hardware level protection for the first and last two 4K word sectors. - At VIH, allows removal of sector protection - At VHH, provides accelerated programming in a factory setting * Persistent Sector Protection - A command sector protection method to lock combinations of individual sectors and sector groups to prevent program or erase operations within that sector - Sectors can be locked and unlocked in-system at VCC level * Package options - 56-ball Fine Pitch BGA - 48-ball Fine pitch BGA - 48-pin TSOP-1 This Data Sheet may be revised by subsequent versions 1 or modifications due to changes in technical specifications. (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 GENERAL DESCRIPTION The PL064/PL032 is a 64/32 Mbit, 3.0 volt-only Page Mode and Simultaneous Read/Write Flash memory device organized as 4/2 Mwords. The devices are offered in the following packages: - 7 mm x 9 mm, 56-Ball Fine-pitch BGA standalone (PL064/PL032) - 8 mm x 6 mm, 48-ball Fine-pitch BGA standalone (PL032) - 48-pin TSOP (PL064/PL032) The word-wide data (x16) appears on DQ15-DQ0. This device can be programmed in-system or in standard EPROM programmers. A 11.0 volt VPP is not required for write or erase operations. The device offers fast page access times of 25 ns, with corresponding random access times of 70 ns, respectively, allowing high speed microprocessors to operate without wait states. To eliminate bus contention the device has separate chip enable (CE#), write enable (WE#) and output enable (OE#) controls. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 2 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 1. Simultaneous Read/Write Operation with Zero Latency The Simultaneous Read/Write architecture provides simultaneous operation by dividing the memory space into 4 banks, which can be considered to be four separate memory arrays as far as certain operations are concerned. The device can improve overall system performance by allowing a host system to program or erase in one bank, then immediately and simultaneously read from another bank with zero latency (with two simultaneous operations operating at any one time). This releases the system from waiting for the completion of a program or erase operation, greatly improving system performance. The device can be organized in both top and bottom sector configurations. The banks are organized as follows: Bank A B C D PL064 Sectors 8 Mbit (4 Kw x 8 and 32 Kw x 15) 24 Mbit (32 Kw x 48) 24 Mbit (32 Kw x 48) 8 Mbit (4 Kw x 8 and 32 Kw x 15) PL032 Sectors 4 Mbit (4 Kw x 8 and 32 Kw x 7) 12 Mbit (32 Kw x 24) 12 Mbit (32 Kw x 24) 4 Mbit (4 Kw x 8 and 32 Kw x 7) 1.1 Page Mode Features The page size is 4 words. After initial page access is accomplished, the page mode operation provides fast read access speed of random locations within that page. 1.2 Standard Flash Memory Features The device requires a single 3.0 volt power supply (2.7 V to 3.6 V) for both read and write functions. Internally generated and regulated voltages are provided for the program and erase operations. The device is entirely command set compatible with the JEDEC 42.4 single-power-supply Flash standard. Commands are written to the command register using standard microprocessor write timing. Register contents serve as inputs to an internal state-machine that controls the erase and programming circuitry. Write cycles also internally latch addresses and data needed for the programming and erase operations. Reading data out of the device is similar to reading from other Flash or EPROM devices. Device programming occurs by executing the program command sequence. The Unlock Bypass mode facilitates faster programming times by requiring only two write cycles to program data instead of four. Device erasure occurs by executing the erase command sequence. The host system can detect whether a program or erase operation is complete by reading the DQ7 (Data# Polling) and DQ6 (toggle) status bits. After a program or erase cycle has been completed, the device is ready to read array data or accept another command. The sector erase architecture allows memory sectors to be erased and reprogrammed without affecting the data contents of other sectors. The device is fully erased when shipped from the factory. Hardware data protection measures include a low VCC detector that automatically inhibits write operations during power transitions. The hardware sector protection feature disables both program and erase operations in any combination of sectors of memory. This can be achieved in-system or via programming equipment. The Erase Suspend/Erase Resume feature enables the user to put erase on hold for any period of time to read data from, or program data to, any sector that is not selected for erasure. True background erase can thus be achieved. If a read is needed from the Secured Silicon Sector area (One Time Program area) after an erase suspend, then the user must use the proper command sequence to enter and exit this region. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 3 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 The Program Suspend/Program Resume feature enables the user to hold the program operation to read data from any sector that is not selected for programming. If a read is needed from the Secured Silicon Sector area, Persistent Protection area, or the CFI area, after a program suspend, then the user must use the proper command sequence to enter and exit this region. The device offers two power-saving features. When addresses have been stable for a specified amount of time, the device enters the automatic sleep mode. The system can also place the device into the standby mode. Power consumption is greatly reduced in both these modes. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 4 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 2. Ordering Information EN29PL064 70 T I P PACKAGING CONTENT (Blank) = Conventional P = Pb Free TEMPERATURE RANGE I = Industrial (-40C to +85C) PACKAGE T = 48-pin TSOP B = 48-Ball Fine Pitch Ball Grid Array (FBGA) 0.80mm pitch, 6mm x 8mm package C =56-Ball Fine Pitch Ball Grid Array (FBGA) 0.80mm pitch, 7mm x 9mm package SPEED 70 = 70ns BASE PART NUMBER EN = Eon Silicon Solution Inc. 29PL = FLASH, 3.0V Read Program Erase, Simultaneous-Read/Write, Page-Mode 064 = 64 Megabit (4 M x 16-Bit) 032 = 32 Megabit (2 M x 16-Bit) 3. Product Selector Guide Part Number Speed Option VCC = 2.7 V - 3.6 V EN29PL032 / EN29PL064 70 70 25 Max Access Time, ns (tACC) Max CE# Access , ns (tCE) Max Page Access, ns (tPACC) Max OE# Access, ns (tOE) This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 5 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 4. BLOCK DIAGRAM Notes 1. 2. RY/BY# is an open drain output. Amax = A21 (PL064), A20 (PL032) This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 6 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 5. Simultaneous Read/Write Block Diagram Note Amax = A21 (PL064), A20 (PL032) This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 7 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 6. Connection Diagrams Figure 6.1 48-pin TSOP Note : PL032: pin 13 (A21) = NC Figure 6.2 48-Ball Fine-Pitch BGA, Top View, Balls Facing Down ( PL032 ) This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 8 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Figure 6.3 56-Ball Fine-Pitch BGA, Top View, Balls Facing Down Note : PL032: C8 (A21) = NC RFU = Reserved for Future Use This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 9 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 7. Pin Description Amax-A0 DQ15-DQ0 CE# OE# WE# VSS NC RY/BY# Address bus 16-bit data inputs/outputs/float Chip Enable Inputs Output Enable Input Write Enable Device Ground Pin Not Connected Internally Ready/Busy output and open drain. When RY/BY#= VIH, the device is ready to accept read operations and commands. When RY/ BY#= VOL, the device is either executing an embedded algorithm or the device is executing a hardware reset operation. Write Protect/Acceleration Input. When WP#/ACC= VIL, the highest and lowest two 4K-word sectors are write protected regardless of other sector protection configurations. When WP#/ACC= VIH, these sector are unprotected unless the PPB is programmed. When WP#/ACC= 11V, program and erase operations are accelerated. Chip Power Supply (2.7 V to 3.6 V) Hardware Reset Pin WP#/ACC VCC RESET# Note Amax = A21 ( PL064), A20 (PL032) 8. Logic Symbol This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 10 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 9. Device Bus Operations This section describes the requirements and use of the device bus operations, which are initiated through the internal command register. The command register itself does not occupy any addressable memory location. The register is a latch used to store the commands, along with the address and data information needed to execute the command. The contents of the register serve as inputs to the internal state machine. The state machine outputs dictate the function of the device. Table 9.1 lists the device bus operations, the inputs and control levels they require, and the resulting output. The following subsections describe each of these operations in further detail. Table 9.1 Device Bus Operations Addresses (Amax-A0) AIN AIN X X X AIN DQ15- DQ0 DOUT DIN High-Z High-Z High-Z DIN Operation CE# Read L Write L Standby Vcc0.3 V Output Disable L Reset X Temporary Sector X Unprotect (High Voltage) OE# L H X H X X WE# H L X H X X RESET# H H Vcc 0.3 V H L VID WP#/ACC X X (Note 2) X (Note 2) X X X Legend: L = Logic Low = VIL, H = Logic High = VIH, VID = 10.5-11.5 V, VHH = 8.5-9.5 V, X = Don't Care, SA = Sector Address, AIN = Address In, DIN = Data In, DOUT = Data Out Notes 1. 2. The sector protect and sector unprotect functions may also be implemented via programming equipment. See High Voltage Sector Protection WP#/ACC must be high when writing to upper two and lower two sectors. 9.1 Requirements for Reading Array Data To read array data from the outputs, the system must drive the OE# and appropriate CE# pins. CE# is the power control. OE# is the output control and gates array data to the output pins. WE# should remain at VIH. The internal state machine is set for reading array data upon device power-up, or after a hardware reset. This ensures that no spurious alteration of the memory content occurs during the power transition. No command is necessary in this mode to obtain array data. Standard microprocessor read cycles that assert valid addresses on the device address inputs produce valid data on the device data outputs. Each bank remains enabled for read access until the command register contents are altered. Refer to Table 21.3 for timing specifications and to Figure 20.3 for the timing diagram. ICC1 in the DC Characteristics table represents the active current specification for reading array data. 9.1.1 Random Read (Non-Page Read) Address access time (tACC) is equal to the delay from stable addresses to valid output data. The chip enable access time (tCE) is the delay from the stable addresses and stable CE# to valid data at the output inputs. The output enable access time is the delay from the falling edge of the OE# to valid data at the output inputs (assuming the addresses have been stable for at least tACC-tOE time). This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 11 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 9.1.2 Page Mode Read The device is capable of fast page mode read and is compatible with the page mode Mask ROM read operation. This mode provides faster read access speed for random locations within a page. Address bits Amax-A2 select a 4 word page, and address bits A1-A0 select a specific word within that page. This is an asynchronous operation with the microprocessor supplying the specific word location. The random or initial page access is tACC or tCE and subsequent page read accesses (as long as the locations specified by the microprocessor falls within that page) is equivalent to tPACC. When CE# is deasserted (=VIH), the reassertion of CE# for subsequent access has access time of tACC or tCE. Here again, CE# selects the device and OE# is the output control and should be used to gate data to the output inputs if the device is selected. Fast page mode accesses are obtained by keeping Amax-A2 constant and changing A1-A0 to select the specific word within that page. Table 9.2 Page Select Word Word 0 Word 1 Word 2 Word 3 A1 0 0 1 1 A0 0 1 0 1 9.2 Simultaneous Read/Write Operation In addition to the conventional features (read, program, erase-suspend read, erase-suspend program, and program-suspend read), the device is capable of reading data from one bank of memory while a program or erase operation is in progress in another bank of memory (simultaneous operation). The bank can be selected by bank addresses (PL064: A21-A19, PL032: A20-A18) with zero latency. The simultaneous operation can execute multi-function mode in the same bank. Table 9.3 Bank Select Bank Bank A Bank B Bank C Bank D PL064: A21-A19, PL032: A20-A18 000 001, 010, 011 100, 101, 110 111 9.3 Writing Commands/Command Sequences To write a command or command sequence (which includes programming data to the device and erasing sectors of memory), the system must drive WE# and CE# to VIL, and OE# to VIH. The device features an Unlock Bypass mode to facilitate faster programming. Once a bank enters the Unlock Bypass mode, only two write cycles are required to program a word, instead of four. Word Program Command Sequence has details on programming data to the device using both standard and Unlock Bypass command sequences. An erase operation can erase one sector or the entire device. Table 9.3 indicates the set of address This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 12 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 space that each sector occupies. A "bank address" is the set of address bits required to uniquely select a bank. Similarly, a "sector address" refers to the address bits required to uniquely select a sector. Command Definitions has details on erasing a sector or the entire chip, or suspending / resuming the erase operation. ICC2 in the DC Characteristics table represents the active current specification for the write mode. See the timing specification tables and timing diagrams in section Reset for write operations. 9.3.1 Accelerated Program Operation The device offers accelerated program operations through the ACC function. This function is primarily intended to allow faster manufacturing throughput at the factory. If the system asserts VHH on this pin, the device automatically enters the aforementioned Unlock Bypass mode, temporarily unprotects any protected sectors, and uses the higher voltage on the pin to reduce the time required for program operations. The system would use a two-cycle program command sequence as required by the Unlock Bypass mode. Removing VHH from the WP#/ACC pin returns the device to normal operation. Note that VHH must not be asserted on WP#/ACC for operations other than accelerated programming, or device damage may result. In addition, the WP#/ACC pin should be raised to VCC when not in use. That is, the WP#/ACC pin should not be left floating or unconnected; inconsistent behavior of the device may result. 9.3.2 Autoselect Functions If the system writes the autoselect command sequence, the device enters the autoselect mode. The system can then read autoselect codes from the internal register (which is separate from the memory array) on DQ15-DQ0. Standard read cycle timings apply in this mode. Refer to the Table 9.6, Secured Silicon Sector Addresses and Autoselect Command Sequence for more information. 9.4 Standby Mode When the system is not reading or writing to the device, it can place the device in the standby mode. In this mode, current consumption is greatly reduced, and the outputs are placed in the high impedance state, independent of the OE# input. The device enters the CMOS standby mode when the CE# and RESET# pins are both held at VCC 0.3 V. (Note that this is a more restricted voltage range than VIH.) If CE# and RESET# are held at VIH, but not within VCC 0.3 V, the device will be in the standby mode, but the standby current will be greater. The device requires standard access time (tCE) for read access when the device is in either of these standby modes, before it is ready to read data. If the device is deselected during erasure or programming, the device draws active current until the operation is completed. ICC3 in DC Characteristics represents the CMOS standby current specification. 9.5 Automatic Sleep Mode The automatic sleep mode minimizes Flash device energy consumption. The device automatically enables this mode when addresses remain stable for tACC + 30 ns. The automatic sleep mode is independent of the CE#, WE#, and OE# control signals. Standard address access timings provide new data when addresses are changed. While in sleep mode, output data is latched and always available to the system. Note that during automatic sleep mode, OE# must be at VIH before the device reduces current to the stated sleep mode specification. ICC5 in DC Characteristics represents the automatic sleep mode current specification. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 13 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 9.6 RESET#: Hardware Reset Pin The RESET# pin provides a hardware method of resetting the device to reading array data. When the RESET# pin is driven low for at least a period of tRP, the device immediately terminates any operation in progress, tristates all output pins, and ignores all read/write commands for the duration of the RESET# pulse. The device also resets the internal state machine to reading array data. The operation that was interrupted should be reinitiated once the device is ready to accept another command sequence, to ensure data integrity. Current is reduced for the duration of the RESET# pulse. When RESET# is held at VSS0.3 V, the device draws CMOS standby current (ICC4). If RESET# is held at VIL but not within VSS0.3 V, the standby current will be greater. The RESET# pin may be tied to the system reset circuitry. A system reset would thus also reset the Flash memory, enabling the system to read the boot-up firmware from the Flash memory. If RESET# is asserted during a program or erase operation, the RY/BY# pin remains a "0" (busy) until the internal reset operation is complete, which requires a time of tREADY (during Embedded Algorithms). The system can thus monitor RY/BY# to determine whether the reset operation is complete. If RESET# is asserted when a program or erase operation is not executing (RY/BY# pin is "1"), the reset operation is completed within a time of tREADY (not during Embedded Algorithms). The system can read data tRH after the RESET# pin returns to VIH. Refer to the tables in AC Characteristic for RESET# parameters and to Figure 20.5 for the timing diagram. 9.7 Output Disable Mode When the OE# input is at VIH, output from the device is disabled. The output pins (except for RY/BY#) are placed in the highest Impedance state This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 14 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Table 9.4 PL064 Sector Architecture (Sheet 1 of 4) Bank Sector SA0 SA1 SA2 SA3 SA4 SA5 SA6 SA7 SA8 SA9 Bank A SA10 SA11 SA12 SA13 SA14 SA15 SA16 SA17 SA18 SA19 SA20 SA21 SA22 Sector Address (A21-A12) 0000000000 0000000001 0000000010 0000000011 0000000100 0000000101 0000000110 0000000111 0000001XXX 0000010XXX 0000011XXX 0000100XXX 0000101XXX 0000110XXX 0000111XXX 0001000XXX 0001001XXX 0001010XXX 0001011XXX 0001100XXX 0001101XXX 0001110XXX 0001111XXX Sector Size (Kwords) 4 4 4 4 4 4 4 4 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 Address Range (x16) 000000h-000FFFh 001000h-001FFFh 002000h-002FFFh 003000h-003FFFh 004000h-004FFFh 005000h-005FFFh 006000h-006FFFh 007000h-007FFFh 008000h-00FFFFh 010000h-017FFFh 018000h-01FFFFh 020000h-027FFFh 028000h-02FFFFh 030000h-037FFFh 038000h-03FFFFh 040000h-047FFFh 048000h-04FFFFh 050000h-057FFFh 058000h-05FFFFh 060000h-067FFFh 068000h-06FFFFh 070000h-077FFFh 078000h-07FFFFh This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 15 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Table 9.4 PL064 Sector Architecture (Sheet 2 of 4) Bank Sector SA23 SA24 SA25 SA26 SA27 SA28 SA29 SA30 SA31 SA32 SA33 SA34 SA35 SA36 SA37 SA38 SA39 SA40 SA41 SA42 SA43 SA44 SA45 Bank B SA46 SA47 SA48 SA49 SA50 SA51 SA52 SA53 SA54 SA55 SA56 SA57 SA58 SA59 SA60 SA61 SA62 SA63 SA64 SA65 SA66 SA67 SA68 SA69 SA70 Sector Address (A21-A12) 0010000XXX 0010001XXX 0010010XXX 0010011XXX 0010100XXX 0010101XXX 0010110XXX 0010111XXX 0011000XXX 0011001XXX 0011010XXX 0011011XXX 0011100XXX 0011101XXX 0011110XXX 0011111XXX 0100000XXX 0100001XXX 0100010XXX 0100011XXX 0100100XXX 0100101XXX 0100110XXX 0100111XXX 0101000XXX 0101001XXX 0101010XXX 0101011XXX 0101100XXX 0101101XXX 0101110XXX 0101111XXX 0110000XXX 0110001XXX 0110010XXX 0110011XXX 0110100XXX 0110101XXX 0110110XXX 0110111XXX 0111000XXX 0111001XXX 0111010XXX 0111011XXX 0111100XXX 0111101XXX 0111110XXX 0111111XXX 16 Sector Size (Kwords) 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 Address Range (x16) 080000h-087FFFh 088000h-08FFFFh 090000h-097FFFh 098000h-09FFFFh 0A0000h-0A7FFFh 0A8000h-0AFFFFh 0B0000h-0B7FFFh 0B8000h-0BFFFFh 0C0000h-0C7FFFh 0C8000h-0CFFFFh 0D0000h-0D7FFFh 0D8000h-0DFFFFh 0E0000h-0E7FFFh 0E8000h-0EFFFFh 0F0000h-0F7FFFh 0F8000h-0FFFFFh 100000h-107FFFh 108000h-10FFFFh 110000h-117FFFh 118000h-11FFFFh 120000h-127FFFh 128000h-12FFFFh 130000h-137FFFh 138000h-13FFFFh 140000h-147FFFh 148000h-14FFFFh 150000h-157FFFh 158000h-15FFFFh 160000h-167FFFh 168000h-16FFFFh 170000h-177FFFh 178000h-17FFFFh 180000h-187FFFh 188000h-18FFFFh 190000h-197FFFh 198000h-19FFFFh 1A0000h-1A7FFFh 1A8000h-1AFFFFh 1B0000h-1B7FFFh 1B8000h-1BFFFFh 1C0000h-1C7FFFh 1C8000h-1CFFFFh 1D0000h-1D7FFFh 1D8000h-1DFFFFh 1E0000h-1E7FFFh 1E8000h-1EFFFFh 1F0000h-1F7FFFh 1F8000h-1FFFFFh This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Table 9.4 PL064 Sector Architecture (Sheet 3 of 4) Bank Sector SA71 SA72 SA73 SA74 SA75 SA76 SA77 SA78 SA79 SA80 SA81 SA82 SA83 SA84 SA85 SA86 SA87 SA88 SA89 SA90 SA91 SA92 SA93 Bank C SA94 SA95 SA96 SA97 SA98 SA99 SA100 SA101 SA102 SA103 SA104 SA105 SA106 SA107 SA108 SA109 SA110 SA111 SA112 SA113 SA114 SA115 SA116 SA117 SA118 Sector Address (A21-A12) 1000000XXX 1000001XXX 1000010XXX 1000011XXX 1000100XXX 1000101XXX 1000110XXX 1000111XXX 1001000XXX 1001001XXX 1001010XXX 1001011XXX 1001100XXX 1001101XXX 1001110XXX 1001111XXX 1010000XXX 1010001XXX 1010010XXX 1010011XXX 1010100XXX 1010101XXX 1010110XXX 1010111XXX 1011000XXX 1011001XXX 1011010XXX 1011011XXX 1011100XXX 1011101XXX 1011110XXX 1011111XXX 1100000XXX 1100001XXX 1100010XXX 1100011XXX 1100100XXX 1100101XXX 1100110XXX 1100111XXX 1101000XXX 1101001XXX 1101010XXX 1101011XXX 1101100XXX 1101101XXX 1101110XXX 1101111XXX 17 Sector Size (Kwords) 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 Address Range (x16) 200000h-207FFFh 208000h-20FFFFh 210000h-217FFFh 218000h-21FFFFh 220000h-227FFFh 228000h-22FFFFh 230000h-237FFFh 238000h-23FFFFh 240000h-247FFFh 248000h-24FFFFh 250000h-257FFFh 258000h-25FFFFh 260000h-267FFFh 268000h-26FFFFh 270000h-277FFFh 278000h-27FFFFh 280000h-287FFFh 288000h-28FFFFh 290000h-297FFFh 298000h-29FFFFh 2A0000h-2A7FFFh 2A8000h-2AFFFFh 2B0000h-2B7FFFh 2B8000h-2BFFFFh 2C0000h-2C7FFFh 2C8000h-2CFFFFh 2D0000h-2D7FFFh 2D8000h-2DFFFFh 2E0000h-2E7FFFh 2E8000h-2EFFFFh 2F0000h-2F7FFFh 2F8000h-2FFFFFh 300000h-307FFFh 308000h-30FFFFh 310000h-317FFFh 318000h-31FFFFh 320000h-327FFFh 328000h-32FFFFh 330000h-337FFFh 338000h-33FFFFh 340000h-347FFFh 348000h-34FFFFh 350000h-357FFFh 358000h-35FFFFh 360000h-367FFFh 368000h-36FFFFh 370000h-377FFFh 378000h-37FFFFh This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Table 9.4 PL064 Sector Architecture (Sheet 4 of 4) Bank Sector SA119 SA120 SA121 SA122 SA123 SA124 SA125 SA126 SA127 SA128 SA129 SA130 SA131 SA132 SA133 SA134 SA135 SA136 SA137 SA138 SA139 SA140 SA141 Sector Address (A21-A12) 1110000XXX 1110001XXX 1110010XXX 1110011XXX 1110100XXX 1110101XXX 1110110XXX 1110111XXX 1111000XXX 1111001XXX 1111010XXX 1111011XXX 1111100XXX 1111101XXX 1111110XXX 1111111000 1111111001 1111111010 1111111011 1111111100 1111111101 1111111110 1111111111 Sector Size (Kwords) 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 4 4 4 4 4 4 4 4 Address Range (x16) 380000h-387FFFh 388000h-38FFFFh 390000h-397FFFh 398000h-39FFFFh 3A0000h-3A7FFFh 3A8000h-3AFFFFh 3B0000h-3B7FFFh 3B8000h-3BFFFFh 3C0000h-3C7FFFh 3C8000h-3CFFFFh 3D0000h-3D7FFFh 3D8000h-3DFFFFh 3E0000h-3E7FFFh 3E8000h-3EFFFFh 3F0000h-3F7FFFh 3F8000h-3F8FFFh 3F9000h-3F9FFFh 3FA000h-3FAFFFh 3FB000h-3FBFFFh 3FC000h-3FCFFFh 3FD000h-3FDFFFh 3FE000h-3FEFFFh 3FF000h-3FFFFFh Bank D This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 18 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Table 9.5 PL032 Sector Architecture (Sheet 1 of 2) Bank Sector SA0 SA 1 SA 2 SA 3 SA 4 SA 5 Bank A SA 6 SA 7 SA 8 SA 9 SA 10 SA 11 SA 12 SA 13 SA 14 SA 15 SA16 SA 17 SA 18 SA 19 SA 20 SA 21 SA 22 SA 23 SA 24 SA25 Bank B SA 26 SA 27 SA 28 SA 29 SA 30 SA 31 SA 32 SA 33 SA 34 SA 35 SA 36 SA 37 SA 38 Sector Address (A20-A12) 000000000 000000001 000000010 000000011 000000100 000000101 000000110 000000111 000001XXX 000010XXX 000011XXX 000100XXX 000101XXX 000110XXX 000111XXX 001000XXX 001001XXX 001010XXX 001011XXX 001100XXX 001101XXX 001110XXX 001111XXX 010000XXX 010001XXX 010010XXX 010011XXX 010100XXX 010101XXX 010110XXX 010111XXX 011000XXX 011001XXX 011010XXX 011011XXX 011100XXX 011101XXX 011110XXX 011111XXX Sector Size (Kwords) 4 4 4 4 4 4 4 4 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 Address Range (x16) 000000h-000FFFh 001000h-001FFFh 002000h-002FFFh 003000h-003FFFh 004000h-004FFFh 005000h-005FFFh 006000h-006FFFh 007000h-007FFFh 008000h-00FFFFh 010000h-017FFFh 018000h-01FFFFh 020000h-027FFFh 028000h-02FFFFh 030000h-037FFFh 038000h-03FFFFh 040000h-047FFFh 048000h-04FFFFh 050000h-057FFFh 058000h-05FFFFh 060000h-067FFFh 068000h-06FFFFh 070000h-077FFFh 078000h-07FFFFh 080000h-087FFFh 088000h-08FFFFh 090000h-097FFFh 098000h-09FFFFh 0A0000h-0A7FFFh 0A8000h-0AFFFFh 0B0000h-0B7FFFh 0B8000h-0BFFFFh 0C0000h-0C7FFFh 0C8000h-0CFFFFh 0D0000h-0D7FFFh 0D8000h-0DFFFFh 0E0000h-0E7FFFh 0E8000h-0EFFFFh 0F0000h-0F7FFFh 0F8000h-0FFFFFh This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 19 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Table 9.5 PL032 Sector Architecture (Sheet 2 of 2) Bank Sector SA39 SA40 SA41 SA42 SA43 SA44 SA45 SA46 SA47 SA48 Bank C SA49 SA50 SA51 SA52 SA53 SA54 SA55 SA56 SA57 SA58 SA59 SA60 SA61 SA62 SA63 SA64 SA65 SA66 SA67 SA68 Bank D SA69 SA70 SA71 SA72 SA73 SA74 SA75 SA76 SA77 Sector Address (A20-A12) 100000XXX 100001XXX 100010XXX 100011XXX 100100XXX 100101XXX 100110XXX 100111XXX 101000XXX 101001XXX 101010XXX 101011XXX 101100XXX 101101XXX 101110XXX 101111XXX 110000XXX 110001XXX 110010XXX 110011XXX 110100XXX 110101XXX 110110XXX 110111XXX 111000XXX 111001XXX 111010XXX 111011XXX 111100XXX 111101XXX 111110XXX 111111000 111111001 111111010 111111011 111111100 111111101 111111110 111111111 Sector Size (Kwords) 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 4 4 4 4 4 4 4 4 Address Range (x16) 100000h-107FFFh 108000h-10FFFFh 110000h-117FFFh 118000h-11FFFFh 120000h-127FFFh 128000h-12FFFFh 130000h-137FFFh 138000h-13FFFFh 140000h-147FFFh 148000h-14FFFFh 150000h-157FFFh 158000h-15FFFFh 160000h-167FFFh 168000h-16FFFFh 170000h-177FFFh 178000h-17FFFFh 180000h-187FFFh 188000h-18FFFFh 190000h-197FFFh 198000h-19FFFFh 1A0000h-1A7FFFh 1A8000h-1AFFFFh 1B0000h-1B7FFFh 1B8000h-1BFFFFh 1C0000h-1C7FFFh 1C8000h-1CFFFFh 1D0000h-1D7FFFh 1D8000h-1DFFFFh 1E0000h-1E7FFFh 1E8000h-1EFFFFh 1F0000h-1F7FFFh 1F8000h-1F8FFFh 1F9000h-1F9FFFh 1FA000h-1FAFFFh 1FB000h-1FBFFFh 1FC000h-1FCFFFh 1FD000h-1FDFFFh 1FE000h-1FEFFFh 1FF000h-1FFFFFh This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 20 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Table 9.6 Secured Silicon Sector Addresses Sector Size 64 words Address Range 000040h-00007Fh Customer-Lockable Area 9.8 Autoselect Mode The autoselect mode provides manufacturer and device identification, and sector protection verification, through identifier codes output on DQ7-DQ0. This mode is primarily intended for programming equipment to automatically match a device to be programmed with its corresponding programming algorithm. However, the autoselect codes can also be accessed in-system through the command register. When using programming equipment, the autoselect mode requires VID on address pin A9. Address pins must be as shown in Table 9.7. In addition, when verifying sector protection, the sector address must appear on the appropriate highest order address bits (see Table 9.3). Table 9.7 show the remaining address bits that are don't care. When all necessary bits have been set as required, the programming equipment may then read the corresponding identifier code on DQ7-DQ0. However, the autoselect codes can also be accessed in-system through the command register, for instances when the device is erased or programmed in a system without access to high voltage on the A9 pin. The command sequence is illustrated in Table 15.1. Note that if a Bank Address (BA) (on address bits PL064: A21-A19, PL032: A20-A18) is asserted during the third write cycle of the autoselect command, the host system can read autoselect data that bank and then immediately read array data from the other bank, without exiting the autoselect mode. To access the autoselect codes in-system, the host system can issue the autoselect command via the command register, as shown in Table 15.1. This method does not require VID. Refer to the Autoselect Command Sequence for more information. Table 9.7 Autoselect Codes (High Voltage Method) Amax to A12 BA A5 to A8 A7 A6 A4 A3 A2 A1 A0 Description CE# OE# WE# A10 A9 DQ15 to DQ0 Manufacturer ID: Eon Read Cycle 1 Device ID Read Cycle 2 Read Cycle 3 L L L L L L H X V ID H L 1 L L X L L L L H H L L L H H H L 001Ch 007Fh 2202h (PL064) 220Ah (PL032) 2201h (PL064) 2201h (PL032) 0001h (protected), 0000h (unprotected) DQ6=1 (customer locked) H 227Eh L H L L H BA X VI D X L L L H H Sector Protection Verification Secured Silicon Indicator Bit (DQ7, DQ6) L H SA X VI D X L L L L L L H BA (See Note) X VI D X X L X L L H H L = Logic Low = VIL, H = Logic High = VIH, BA = Bank Address, SA = Sector Address, X = Don't care. Note 1. A8=H is recommended for Manufacturing ID check. If a manufacturing ID is read with A8=L, the chip will output a configuration code 7Fh. 2. A9 = VBID is for HV A9 Autoselect mode only. A9 must be Vcc (CMOS logic level) for Command Autoselect Mode. When Polling the Secured Silicon indicator bit the Bank Address (BA) should be set within the address range 004000h-03FFFFh. B This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 21 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 9.9 Selecting a Sector Protection Mode Table 9.8 PL064 Boot Sector/Sector Block Addresses for Protection/Unprotection Sector SA0 SA1 SA2 SA3 SA4 SA5 SA6 SA7 SA8 SA9 SA10 SA11-SA14 SA15-SA18 SA19-SA22 SA23-SA26 SA27-SA30 SA31-SA34 SA35-SA38 SA39-SA42 SA43-SA46 SA47-SA50 SA51-SA54 SA55-SA58 SA59-SA62 SA63-SA66 SA67-SA70 SA71-SA74 SA75-SA78 SA79-SA82 SA83-SA86 SA87-SA90 SA91-SA94 SA95-SA98 SA99-SA102 SA103-SA106 SA107-SA110 SA111-SA114 SA115-SA118 SA119-SA122 SA123-SA126 SA127-SA130 SA131 SA132 SA133 SA134 SA135 SA136 SA137 SA138 SA139 SA140 SA141 A21-A12 0000000000 0000000001 0000000010 0000000011 0000000100 0000000101 0000000110 0000000111 0000001XXX 0000010XXX 0000011XXX 00001XXXXX 00010XXXXX 00011XXXXX 00100XXXXX 00101XXXXX 00110XXXXX 00111XXXXX 01000XXXXX 01001XXXXX 01010XXXXX 01011XXXXX 01100XXXXX 01101XXXXX 01110XXXXX 01111XXXXX 10000XXXXX 10001XXXXX 10010XXXXX 10011XXXXX 10100XXXXX 10101XXXXX 10110XXXXX 10111XXXXX 11000XXXXX 11001XXXXX 11010XXXXX 11011XXXXX 11100XXXXX 11101XXXXX 11110XXXXX 1111100XXX 1111101XXX 1111110XXX 1111111000 1111111001 1111111010 1111111011 1111111100 1111111101 1111111110 1111111111 Sector/Sector Block Size 4 Kwords 4 Kwords 4 Kwords 4 Kwords 4 Kwords 4 Kwords 4 Kwords 4 Kwords 32 Kwords 32 Kwords 32 Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 128 (4x32) Kwords 32 Kwords 32 Kwords 32 Kwords 4 Kwords 4 Kwords 4 Kwords 4 Kwords 4 Kwords 4 Kwords 4 Kwords 4 Kwords This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 22 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 The device is shipped with all sectors unprotected. Optional Eon programming services enable programming and protecting sectors at the factory prior to shipping the device. Contact your local sales office for details. It is possible to determine whether a sector is protected or unprotected. See the Table 9.6 Secured Silicon Sector Addresses for details. 10. Sector Protection The PL064, and PL032 features several levels of sector protection, which can disable both the program and erase operations in certain sectors or sector groups: 10.1 Persistent Sector Protection A command sector protection method that replaces the old 11 V controlled protection method. 10.2 WP# Hardware Protection A write protect pin that can prevent program or erase operations in sectors SA0, SA1, SA140 and SA141. (PL064) / SA0, SA1, SA76 and SA77. (PL032) The WP# Hardware Protection feature is always available, independent of the software managed protection method chosen. 10.3 Selecting a Sector Protection Mode All parts default to operate in the Persistent Sector Protection mode. There are two one-time programmable nonvolatile bits that define which sector protection method will be used. The device is shipped with all sectors unprotected. Optional Eon's programming services enable programming and protecting sectors at the factory prior to shipping the device. Contact your local sales office for details. It is possible to determine whether a sector is protected or unprotected. See Autoselect Mode for details. 11. Persistent Sector Protection The Persistent Sector Protection method replaces the 11 V controlled protection method in previous flash devices. This new method provides the sector protection states: Persistently Locked--The sector is protected and cannot be changed. To achieve these states, two types of "bits" are used: Persistent Protection Bit Persistent Protection Bit Lock 11.1 Persistent Protection Bit (PPB) A single Persistent (non-volatile) Protection Bit is assigned to a maximum four sectors (see the sector address tables for specific sector protection groupings). All 4 Kword boot-block sectors have individual sector Persistent Protection Bits (PPBs) for greater flexibility. Each PPB is individually modifiable through the PPB Write Command. The device erases all PPBs in parallel. If any PPB requires erasure, the device must be instructed to preprogram all of the sector PPBs prior to PPB erasure. Otherwise, a previously erased sector PPBs can potentially be over-erased. The flash device does not have a built-in means of preventing sector PPBs over-erasure. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 23 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 11.2 Persistent Protection Bit Lock (PPB Lock) The Persistent Protection Bit Lock (PPB Lock) is a global volatile bit. When set to "1", the PPBs cannot be changed. When cleared ("0"), the PPBs are changeable. There is only one PPB Lock bit per device. The PPB Lock is cleared after power-up or hardware reset. There is no command sequence to unlock the PPB Lock. The WP#/ACC write protect pin adds a final level of hardware protection to sectors SA0, SA1, SA140 and SA141. (PL064) / SA0, SA1, SA76 and SA77. (PL032). When this pin is low it is not possible to change the contents of these sectors. These sectors generally hold system boot code. The WP#/ACC pin can prevent any changes to the boot code that could override the choices made while setting up sector protection during system initialization. For customers who are concerned about malicious viruses there is another level of security - the persistently locked state. To persistently protect a given sector or sector group, the PPBs associated with that sector need to be set to "1". Once all PPBs are programmed to the desired settings, the PPB Lock should be set to "1". Setting the PPB Lock automatically disables all program and erase commands to the Non-Volatile PPBs. In effect, the PPB Lock "freezes" the PPBs into their current state. The only way to clear the PPB Lock is to go through a power cycle. The best protection is achieved by executing the PPB lock bit set command early in the boot code, and protect the boot code by holding WP#/ACC = VIL. In summary, if the PPB is set, and the PPB lock is set, the sector is protected and the protection can not be removed until the next power cycle clears the PPB lock. If the user attempts to program or erase a protected sector, the device ignores the command and returns to read mode. A program command to a protected sector enables status polling for approximately 1 s before the device returns to read mode without having modified the contents of the protected sector. An erase command to a protected sector enables status polling for approximately 50 s after which the device returns to read mode without having erased the protected sector. The programming of the PPB, and PPB lock for a given sector can be verified by writing a PPB/ PPB lock verify command to the device. There is an alternative means of reading the protection status. Take RESET# to VIL and hold WE# at VIH. (The high voltage A9 Autoselect Mode also works for reading the status of the PPBs). Scanning the addresses (A18-A11) while (A6, A1, A0) = (0, 1, 0) will produce a logical `1" code at device output DQ0 for a protected sector or a "0" for an unprotected sector. In this mode, the other addresses are don't cares. Address location with A1 = VIL are reserved for autoselect manufacturer and device codes. 12. Write Protect (WP#) The Write Protect feature provides a hardware method of protecting the upper two and lower two sectors without using VID. This function is provided by the WP# pin and overrides the previously discussed High Voltage Sector Protection method. If the system asserts VIL on the WP#/ACC pin, the device disables program and erase functions in the two outermost 4 Kword sectors on both ends of the flash array independent of whether it was previously protected or unprotected. If the system asserts VIH on the WP#/ACC pin, the device reverts the upper two and lower two sectors to whether they were last set to be protected or unprotected. That is, sector protection or unprotection for these sectors depends on whether they were last protected or unprotected using the method described in the High Voltage Sector Protection . Note that the WP#/ACC pin must not be left floating or unconnected; inconsistent behavior of the device may result. 13. High Voltage Sector Protection Sector protection and unprotection may also be implemented using programming equipment. The procedure requires high voltage (VID) to be placed on the RESET# pin. Refer to Figure 13.1 for details on this procedure. Note that for sector unprotect, all unprotected sectors must first be protected prior to the first sector write cycle. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 24 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Figure 13.1 In-System Sector Protection/Sector Unprotection Algorithms This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 25 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 13.1 Temporary Sector Unprotect This feature allows temporary unprotection of previously protected sectors to change data in-system. The Sector Unprotect mode is activated by setting the RESET# pin to VID. During this mode, formerly protected sectors can be programmed or erased by selecting the sector addresses. Once VID is removed from the RESET# pin, all the previously protected sectors are protected again. Figure 13.2 shows the algorithm, and Figure 21.1 shows the timing diagrams, for this feature. While PPB lock is set, the device cannot enter the Temporary Sector Unprotection Mode. Figure 13.2 Temporary Sector Unprotect Operation Notes: 1. 2. All protected sectors unprotected (If WP#/ACC = VIL, upper two and lower two sectors will remain protected). All previously protected sectors are protected once again 13.2 Secured Silicon Sector Flash Memory Region The Secured Silicon Sector feature provides a Flash memory region that enables permanent part identification through an Electronic Serial Number (ESN). The 64-word Secured Silicon sector is customer-lockable words that can be programmed and locked by the customer. The Secured Silicon sector is located at addresses 000040h-00007Fh. Indicator bit DQ6 is used to indicate the customer locked status of the part. The system accesses the Secured Silicon Sector through a command sequence (see the Enter/Exit Secured Silicon Sector Command Sequence). After the system has written the Enter Secured Silicon Sector command sequence, it may read the Secured Silicon Sector by using the addresses normally occupied by the boot sectors. This mode of operation continues until the system issues the Exit Secured Silicon Sector command sequence, or until power is removed from the device. Once the Enter SecSi Sector Command sequence has been entered, the standard array cannot be accessed until the Exit SecSi Sector command has been entered or the device has been reset. On power-up, or following a hardware reset, the device reverts to sending commands to the normal address space. Note that the ACC function and unlock bypass modes are not available when the Secured Silicon Sector is enabled. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 26 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 13.2.1 Customer-Lockable Area (64 words) The customer-lockable area of the Secured Silicon Sector (000040h-00007Fh) is shipped unprotected, which allows the customer to program and optionally lock the area as appropriate for the application. The Secured Silicon Sector Customer-locked Indicator Bit (DQ6) is shipped as "0" and can be permanently locked to "1" by issuing the Secured Silicon Protection Bit Program Command. The Secured Silicon Sector can be read any number of times, but can be programmed and locked only once. Note that the accelerated programming (ACC) and unlock bypass functions are not available when programming the Secured Silicon Sector. The Customer-lockable Secured Silicon Sector area can be protected using one of the following procedures: Write the three-cycle Enter Secured Silicon Sector Region command sequence, and then follow the in-system sector protect algorithm as shown in Figure 13.1 , except that RESET# may be at either VIH or VID. This allows in-system protection of the Secured Silicon Sector Region without raising any device pin to a high voltage. Note that this method is only applicable to the Secured Silicon Sector. To verify the protect/unprotect status of the Secured Silicon Sector, follow the algorithm shown in Figure 13.3. Once the Secured Silicon Sector is locked and verified, the system must write the Exit Secured Silicon Sector Region command sequence to return to reading and writing the remainder of the array. The Secured Silicon Sector lock must be used with caution since, once locked, there is no procedure available for unlocking the Secured Silicon Sector area and none of the bits in the Secured Silicon Sector memory space can be modified in any way. 13.2.2 Secured Silicon Sector Protection Bits The Secured Silicon Sector Protection Bits prevent programming of the Secured Silicon Sector memory area. Once set, the Secured Silicon Sector memory area contents are non-modifiable. Figure 13.3 Secured Silicon Sector Protect Verify This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 27 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 13.3 Hardware Data Protection The command sequence requirement of unlock cycles for programming or erasing provides data protection against inadvertent writes. In addition, the following hardware data protection measures prevent accidental erasure or programming, which might otherwise be caused by spurious system level signals during VCC power-up and power-down transitions, or from system noise. 13.3.1 Low VCC Write Inhibit When VCC is less than VLKO, the device does not accept any write cycles. This protects data during VCC power-up and power-down. The command register and all internal program/erase circuits are disabled, and the device resets to the read mode. Subsequent writes are ignored until VCC is greater than VLKO. The system must provide the proper signals to the control pins to prevent unintentional writes when VCC is greater than VLKO. 13.3.2 Write Pulse "Glitch" Protection Noise pulses of less than 3 ns (typical) on OE#, CE#, or WE# do not initiate a write cycle. 13.3.3 Logical Inhibit Write cycles are inhibited by holding any one of OE# = VIL, CE# = VIH or WE# = VIH. To initiate a write cycle, CE# and WE# must be a logical zero while OE# is a logical one. 13.3.4 Power-Up Write Inhibit If WE# = CE# = VIL and OE# = VIH during power up, the device does not accept commands on the rising edge of WE#. The internal state machine is automatically reset to the read mode on power-up. 14. Common Flash Memory Interface (CFI) The Common Flash Interface (CFI) specification outlines device and host system software interrogation handshake, which allows specific vendor-specified software algorithms to be used for entire families of devices. Software support can then be device-independent, JEDEC ID-independent, and forward- and backward-compatible for the specified flash device families. Flash vendors can standardize their existing interfaces for long-term compatibility. This device enters the CFI Query mode when the system writes the CFI Query command, 98h, to address 55h, any time the device is ready to read array data. The system can read CFI information at the addresses given in Table 14.1 to Table 14.4. To terminate reading CFI data, the system must write the reset command. The CFI Query mode is not accessible when the device is executing an Embedded Program or embedded Erase algorithm. The system can also write the CFI query command when the device is in the autoselect mode. The device enters the CFI query mode, and the system can read CFI data at the addresses given in Table 14.1 to Table 14.4. The system must write the reset command to return the device to reading array data. For further information, please refer to the CFI Specification and CFI Publication 100. Contact your local sales office for copies of these documents. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 28 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Table 14.1 CFI Query Identification String Addresses 10h 11h 12h 13h 14h 15h 16h 17h 18h 19h 1Ah Data 0051h 0052h 0059h 0002h 0000h 0040h 0000h 0000h 0000h 0000h 0000h Description Query Unique ASCII string "QRY" Primary OEM Command Set Address for Primary Extended Table Alternate OEM Command Set (00h = none exists) Address for Alternate OEM Extended Table (00h = none exists) Table 14.2 System Interface String Addresses 1Bh 1Ch 1Dh 1Eh 1Fh 20h 21h 22h 23h 24h 25h 26h Data 0027h 0036h 0000h 0000h 0003h 0004h 0009h 0000h 0005h 0005h 0004h 0004h Description VCC Min. (write/erase) D7-D4: volt, D3-D0: 100 millivolt VCC Max. (write/erase) D7-D4: volt, D3-D0: 100 millivolt VPP Min. voltage (00h = no VPP pin present) VPP Max. voltage (00h = no VPP pin present) Typical timeout per single byte/word write 2 s Typical timeout for Min. size buffer write 2 s (00h = not supported) Typical timeout per individual block erase 2 ms Typical timeout for full chip erase 2 ms (00h = not supported) Max. timeout for byte/word write 2 times typical Max. timeout for buffer write 2 times typical Max. timeout per individual block erase 2N times typical Max. timeout for full chip erase 2N times typical (00h = not supported) N N N N N N Table 14.3 Device Geometry Definition Addresses 27h 28h 29h 2Ah 2Bh 2Ch 2Dh 2Eh 2Fh 30h 31h 32h 33h 34h 35h 36h 37h 38h Data 0017h (PL064) 0016h (PL032) 0001h 0000h 0006h 0000h 0003h 0007h 0000h 0020h 0000h 007Dh (PL064) 003Dh (PL032) 0000h 0000h 0001h 0007h 0000h 0020h 0000h Description Device Size = 2 byte Flash Device Interface description (refer to CFI publication 100) Max. number of byte in multi-byte write = 2 (00h = not supported) Number of Erase Block Regions within device Erase Block Region 1 Information (refer to the CFI specification or CFI publication 100) N N Erase Block Region 2 Information (refer to the CFI specification or CFI publication 100) Erase Block Region 3 Information (refer to the CFI specification or CFI publication 100) This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 29 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 39h 3Ah 3Bh 3Ch 0000h 0000h 0000h 0000h Erase Block Region 4 Information (refer to the CFI specification or CFI publication 100) Table 14.4 Primary Vendor-Specific Extended Query Addresses 40h 41h 42h 43h 44h 45h 46h 47h 48h 49h 4Ah 4Bh 4Ch 4Dh 4Eh Data 0050h 0052h 0049h 0031h 0034h 0008h 0002h 0001h 0001h 0002h 0077h (PL064) 003Fh (PL032) 0000h 0001h 0085h 0095h Description Query-unique ASCII string "PRI" Major version number, ASCII (reflects modifications to the silicon) Minor version number, ASCII (reflects modifications to the CFI table) Address Sensitive Unlock (Bits 1-0) 0 = Required, 1 = Not Required Silicon Revision Number (Bits 7-2) Erase Suspend 0 = Not Supported, 1 = To Read Only, 2 = To Read & Write Sector Protect 0 = Not Supported, X = Number of sectors in per group Sector Temporary Unprotect 00 = Not Supported, 01 = Supported Sector Protect/Unprotect scheme 00h = High Voltage Sector Protection 01h = High Voltage + In-System Sector Protection 02h = HV + In-System Software Command Sector Protection Simultaneous Operation 00 = Not Supported, X = Number of Sectors excluding Bank 1 Burst Mode Type 00 = Not Supported, 01 = Supported Page Mode Type 00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page ACC (Acceleration) Supply Minimum 00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV ACC (Acceleration) Supply Maximum 00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV Table 14.4 Primary Vendor-Specific Extended Query (Continued) Addresses 4Fh 50h 51h 52h 53h 54h 55h 56h Data 0001h 0001h 0001h 0007h 000Fh 0009h 0005h 0005h Description Top/Bottom Boot Sector Flag 00h = Uniform device, 01h = Both top and bottom boot with write protect, 02h = Bottom Boot Device, 03h = Top Boot Device, 04h = Both Top and Bottom Program Suspend 0 = Not supported, 1 = Supported Unlock Bypass 00 = Not Supported, 01 = Supported Secured Silicon Sector (Customer OTP Area) Size 2N bytes Hardware Reset Low Time-out during an embedded algorithm to read N mode Maximum 2 ns Hardware Reset Low Time-out not during an embedded algorithm to read N mode Maximum 2 ns Erase Suspend Latency Maximum 2 s Program Suspend Latency Maximum 2 s N N This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 30 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 57h 58h 59h 5Ah 5Bh 0004h 0017h (PL064) 000Fh (PL032) 0030h (PL064) 0018h (PL032) 0030h (PL064) 0018h (PL032) 0017h (PL064) 000Fh (PL032) Bank Organization 00 = Data at 4Ah is zero, X = Number of Banks Bank 1 Region Information X = Number of Sectors in Bank 1 Bank 2 Region Information X = Number of Sectors in Bank 2 Bank 3 Region Information X = Number of Sectors in Bank 3 Bank 4 Region Information X = Number of Sectors in Bank 4 15. Command Definitions Writing specific address and data commands or sequences into the command register initiates device operations. Table 15.1 defines the valid register command sequences. Writing incorrect address and data values or writing them in the improper sequence may place the device in an unknown state. A reset command is then required to return the device to reading array data. All addresses are latched on the falling edge of WE# or CE#, whichever happens later. All data is latched on the rising edge of WE# or CE# , whichever happens first. Refer to AC Characteristic for timing diagrams. 15.1 Reading Array Data The device is automatically set to reading array data after device power-up. No commands are required to retrieve data. Each bank is ready to read array data after completing an Embedded Program or Embedded Erase algorithm. After the device accepts an Erase Suspend command, the corresponding bank enters the erasesuspend-read mode, after which the system can read data from any non-erase-suspended sector within the same bank. The system can read array data using the standard read timing, except that if it reads at an address within erase-suspended sectors, the device outputs status data. After completing a programming operation in the Erase Suspend mode, the system may once again read array data with the same exception. See Erase Suspend/Erase Resume Commands for more information. After the device accepts a Program Suspend command, the corresponding bank enters the program-suspend-read mode, after which the system can read data from any non-programsuspended sector within the same bank. See Program Suspend/Program Resume Commands for more information. The system must issue the reset command to return a bank to the read (or erase-suspend-read) mode if DQ5 goes high during an active program or erase operation, or if the bank is in the autoselect mode. See the next section, Reset Command , for more information. See also Requirements for Reading Array Data for more information. The table AC Characteristic provides the read parameters, and Figure 16.2 shows the timing diagram. 15.2 Reset Command Writing the reset command resets the banks to the read or erase-suspend-read mode. Address bits are don't cares for this command. The reset command may be written between the sequence cycles in an erase command sequence before erasing begins. This resets the bank to which the system was writing to the read mode. Once erasure begins, however, the device ignores reset commands until the operation is complete. The reset command may be written between the sequence cycles in a program command sequence before programming begins. This resets the bank to which the system was writing to the read mode. If the program command sequence is written to a bank that is in the Erase Suspend mode, writing the reset command returns that bank to the erase-suspend-read mode. Once programming begins, however, the device ignores reset commands until the operation is complete. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 31 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 The reset command may be written between the sequence cycles in an autoselect command sequence. Once in the autoselect mode, the reset command must be written to return to the read mode. If a bank entered the autoselect mode while in the Erase Suspend mode, writing the reset command returns that bank to the erase-suspend-read mode. If DQ5 goes high during a program or erase operation, writing the reset command returns the banks to the read mode (or erase-suspend-read mode if that bank was in Erase Suspend and programsuspend-read mode if that bank was in Program Suspend). 15.3 Autoselect Command Sequence The autoselect command sequence allows the host system to access the manufacturer and device codes, and determine whether or not a sector is protected. The autoselect command sequence may be written to an address within a bank that is either in the read or erase-suspend-read mode. The autoselect command may not be written while the device is actively programming or erasing in the other bank. The autoselect command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle that contains the bank address and the autoselect command. The bank then enters the autoselect mode. The system may read any number of autoselect codes without reinitiating the command sequence. Table 15.1 shows the address and data requirements. To determine sector protection information, the system must write to the appropriate bank address (BA) and sector address (SA). The system must write the reset command to return to the read mode (or erase-suspend-read mode if the bank was previously in Erase Suspend). 15.4 Enter/Exit Secured Silicon Sector Command Sequence The Secured Silicon Sector region provides a secured data area containing a random, eight word electronic serial number (ESN). The system can access the Secured Silicon Sector region by issuing the three-cycle Enter Secured Silicon Sector command sequence. The device continues to access the Secured Silicon Sector region until the system issues the four-cycle Exit Secured Silicon Sector command sequence. The Exit Secured Silicon Sector command sequence returns the device to normal operation. The Secured Silicon Sector is not accessible when the device is executing an Embedded Program or embedded Erase algorithm. Table 15.1 shows the address and data requirements for both command sequences. See also Secured Silicon Sector Flash Memory Region for further information. Note that the ACC function and unlock bypass modes are not available when the Secured Silicon Sector is enabled. 15.5 Word Program Command Sequence Programming is a four-bus-cycle operation. The program command sequence is initiated by writing two unlock write cycles, followed by the program set-up command. The program address and data are written next, which in turn initiate the Embedded Program algorithm. The system is not required to provide further controls or timings. The device automatically provides internally generated program pulses and verifies the programmed cell margin. Table 15.1 shows the address and data requirements for the program command sequence. Note that the Secured Silicon Sector, autoselect, and CFI functions are unavailable when a [program/erase] operation is in progress. When the Embedded Program algorithm is complete, that bank then returns to the read mode and addresses are no longer latched. The system can determine the status of the program operation by using DQ7, DQ6, or RY/BY#. Refer to Write Operation Status for information on these status bits. Any commands written to the device during the Embedded Program Algorithm are ignored. Note that a hardware reset immediately terminates the program operation. The program command sequence should be reinitiated once that bank has returned to the read mode, to ensure data integrity. Note that the Secured Silicon Sector, autoselect and CFI functions are unavailable when the Secured Silicon Sector is enabled. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 32 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Programming is allowed in any sequence and across sector boundaries. A bit cannot be programmed from "0" back to a "1." Attempting to do so may cause that bank to set DQ5 = 1, or cause the DQ7 and DQ6 status bits to indicate the operation was successful. However, a succeeding read will show that the data is still "0." Only erase operations can convert a "0" to a "1." 15.5.1 Unlock Bypass Command Sequence The unlock bypass feature allows the system to program data to a bank faster than using the standard program command sequence. The unlock bypass command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle containing the unlock bypass command, 20h. That bank then enters the unlock bypass mode. A two-cycle unlock bypass program command sequence is all that is required to program in this mode. The first cycle in this sequence contains the unlock bypass program command, A0h; the second cycle contains the program address and data. Additional data is programmed in the same manner. This mode dispenses with the initial two unlock cycles required in the standard program command sequence, resulting in faster total programming time. Table 15.1 shows the requirements for the command sequence. During the unlock bypass mode, only the Unlock Bypass Program and Unlock Bypass Reset commands are valid. To exit the unlock bypass mode, the system must issue the two-cycle unlock bypass reset command sequence. The device offers accelerated program operations through the WP#/ACC pin. When the system asserts VHH on the WP#/ACC pin, the device automatically enters the Unlock Bypass mode. The system may then write the two-cycle Unlock Bypass program command sequence. The device uses the higher voltage on the WP#/ ACC pin to accelerate the operation. Note that the WP#/ACC pin must not be at VHH any operation other than accelerated programming, or device damage may result. In addition, the WP#/ACC pin must not be left floating or unconnected; inconsistent behavior of the device may result. Figure 15.1 illustrates the algorithm for the program operation. Refer to the table Erase/Program Operations for parameters, and Figure 20.6 for timing diagrams. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 33 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Figure 15.1 Program Operation Note See Table 15.1 for program command sequence. 15.6 Write Buffer Programming Operation Write Buffer Programming allows the system to write a maximum of 32 words in one programming operation. The results in a faster effective word programming time than the standard "word" programming algorithms. The Write Buffer Programming command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle containing the Write Buffer Load command written at the starting address in which programming will occur. At this point, the system writes the number of " word locations minus 1 " that will be loaded into the page buffer at the starting address in which programming will occur. This tells the device how many write buffer addresses will be loaded with data and therefore when to expect the "Program Buffer of Flash" confirm command. The number of locations to program cannot exceed the size of the write buffer or the operation will abort. (NOTE: the number loaded = the number of locations to program minus 1. For example, if the system will program 6 address locations, then 05h should be written to the device.) The system then writes the starting address/data combination. This starting address is the first address/data pair to be programmed, and selects the "write-buffer-page" address. All subsequent address/data pairs must fall within the "selected-write-buffer-page". The "write- buffer-page" is selected by using the addresses Amax- A5 The "write- buffer-page" addresses must be the same for all address/data pairs loaded into the write buffer. (This means Write Buffer Programming cannot be performed across multiple "writebuffer-page". This also means that Write Buffer Programming cannot be performed across multiple sectors. If the system attempts to load programming data outside of the selected "write- buffer-page", the operation will ABORT.) This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw 34 Rev. D, Issue Date: 2008/03/27 EN29PL064/032 After writing the Starting Address/Data pair, the system then writes the remaining address/data pars into the write buffer. Write buffer locations may be loaded in any order. Note that if a Write Buffer address location is loaded multiple times, the "address/data pair" counter will be decremented for every data load operation. Also, the last data loaded at a location before the "Program Buffer to Flash" confirm command will be programmed into the device. It is the software's responsibility to comprehend ramifications of loading a write-buffer location more than once. The counter decrements for each data load operation, NOT for each unique write-bufferaddress location. Once the specified number of write buffer locations have been loaded, the system must then write the "Program Buffer to Flash" command at the Sector Address. Any other address/data write combinations will abort the Write Buffer Programming operation. The device will then "go busy". The Data Bar polling techniques should be used while monitoring the last address location loaded into the write buffer. This eliminates the need to store an address in memory because the system can load the last address location, issue the program confirm command at the last loaded address location, and then data bar poll at that same address. DQ7, DQ6, DQ5, DQ2, and DQ1 should be monitored to determine the device status during Write Buffer Programming. The write-buffer "embedded" programming operation can be suspended using the standard suspend/resume commands. Upon successful completion of the Write Buffer Programming operation, the device will return to READ mode. The Write Buffer Programming Sequence is ABORTED under any of the following conditions: Load a value that is greater than the page buffer size during the "Number of Locations to Program" step. Write to an address in a sector different than the one specified during the "Write-Buffer-Load" command. Write an Address/Data pair to a different write-buffer-page than the one selected by the "Starting Address" during the "write buffer data loading" stage of the operation. Write data other than the "Confirm Command" after the specified number of "data load" cycle. The ABORT condition is indicated by DQ = 1, DQ7 = DATA# (for the "last address location loaded") , DQ6 = TOGGLE, DQ5 = 0. This indicates that the Write Buffer Programming Operation was ABORTED. A "Write-to-Buffer-Abort reset" command sequence is required when using the Write Buffer Programming feature in Unlock Bypass mode. Note that the Secured Silicon sector, autoselect, and CFI functions are unavailable when a program operation is in progress. Use of the write buffer is strongly recommended for programming when multiple words are to be programmed. Write buffer programming is allowed in any sequence of memory (or address) locations. These flash devices are capable of handling multiple write buffer programming operations on the same write buffer address range without intervening erases. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 35 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 36 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 15.7 Chip Erase Command Sequence Chip erase is a six bus cycle operation. The chip erase command sequence is initiated by writing two unlock cycles, followed by a set-up command. Two additional unlock write cycles are then followed by the chip erase command, which in turn invokes the Embedded Erase algorithm. The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically preprograms and verifies the entire memory for an all zero data pattern prior to electrical erase. The system is not required to provide any controls or timings during these operations. Table 15.1 shows the address and data requirements for the chip erase command sequence. When the Embedded Erase algorithm is complete, that bank returns to the read mode and addresses are no longer latched. The system can determine the status of the erase operation by using DQ7, DQ6, DQ2, or RY/ BY#. Refer to Write Operation Status for information on these status bits. Any commands written during the chip erase operation are ignored. Note that Secured Silicon Sector, autoselect, and CFI functions are unavailable when a [program/erase] operation is in progress. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the chip erase command sequence should be reinitiated once that bank has returned to reading array data, to ensure data integrity. Figure 15.2 illustrates the algorithm for the erase operation. Refer to the tables in Erase/Program Operations for parameters, and Figure 20.8 for timing diagrams. 15.8 Sector Erase Command Sequence Sector erase is a six bus cycle operation. The sector erase command sequence is initiated by writing two unlock cycles, followed by a set-up command. Two additional unlock cycles are written, and are then followed by the address of the sector to be erased, and the sector erase command. Table 15.1 shows the address and data requirements for the sector erase command sequence. The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically programs and verifies the entire memory for an all zero data pattern prior to electrical erase. The system is not required to provide any controls or timings during these operations. Note that Secured Silicon Sector, autoselect, and CFI functions are unavailable when a [program/erase] operation is in progress. The system can monitor DQ3 to determine if the sector erase timer has timed out (See the section on DQ3: Sector Erase Timer). The time-out begins from the rising edge of the final WE# pulse in the command sequence. When the Embedded Erase algorithm is complete, the bank returns to reading array data and addresses are no longer latched. Note that while the Embedded Erase operation is in progress, the system can read data from the non-erasing bank. The system can determine the status of the erase operation by reading DQ7, DQ6, DQ2, or RY/BY# in the erasing bank. Refer to Write Operation Status for information on these status bits. Once the sector erase operation has begun, only the Erase Suspend command is valid. All other commands are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the sector erase command sequence should be reinitiated once that bank has returned to reading array data, to ensure data integrity. Figure 15.2 illustrates the algorithm for the erase operation. Refer to the tables in Erase/Program Operations for parameters, and Figure 20.8 for timing diagrams. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 37 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Figure 15.2 Erase Operation Notes 1. 2. See Table 15.1 for erase command sequence. See the section on DQ3 for information on the sector erase timer. 15.9 Erase Suspend/Erase Resume Commands The Erase Suspend command, B0h, allows the system to interrupt a sector erase operation and then read data from, or program data to, any sector not selected for erasure. The bank address is required when writing this command. This command is valid only during the sector erase operation, including the 80 s time-out period during the sector erase command sequence. The Erase Suspend command is ignored if written during the chip erase operation or Embedded Program algorithm. When the Erase Suspend command is written during the sector erase operation, the device requires a maximum of 35 s to suspend the erase operation. However, when the Erase Suspend command is written during the sector erase time-out, the device immediately terminates the time-out period and suspends the erase operation. Addresses are "don't-cares" when writing the Erase suspend command. After the erase operation has been suspended, the bank enters the erase-suspend-read mode. The system can read data from or program data to any sector not selected for erasure. (The device "erase suspends" all sectors selected for erasure.) Reading at any address within erase-suspended sectors produces status information on DQ7-DQ0. The system can use DQ7, or DQ6 and DQ2 together, to determine if a sector is actively erasing or is erase-suspended. Refer to Write Operation Status for information on these status bits. After an erase-suspended program operation is complete, the bank returns to the erase-suspendread mode. The system can determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard Word Program operation. Refer to Write Operation Status for more information. In the erase-suspend-read mode, the system can also issue the autoselect command sequence. The device allows reading autoselect codes even at addresses within erasing sectors, since the codes are not stored in the memory array. When the device exits the autoselect mode, the device reverts to the Erase Suspend mode, and is ready for another valid operation. Refer to Table 9.6, Secured Silicon Sector Addresses and Autoselect Command Sequence for details. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 38 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 To resume the sector erase operation, the system must write the Erase Resume command (address bits are don't care). The bank address of the erase-suspended bank is required when writing this command. Further writes of the Resume command are ignored. Another Erase Suspend command can be written after the chip has resumed erasing. If the Secured Silicon Sector Protection Bit is verified as programmed without margin, the Secured Silicon Sector Protection Bit Program Command should be reissued to improve program margin. After programming a PPB, two additional cycles are needed to determine whether the PPB has been programmed with margin. If the PPB has been programmed without margin, the program command should be reissued to improve the program margin. Also note that the total number of PPB program/erase cycles is limited to 100 cycles. Cycling the PPBs beyond 100 cycles is not guaranteed. After erasing the PPBs, two additional cycles are needed to determine whether the PPB has been erased with margin. If the PPBs has been erased without margin, the erase command should be reissued to improve the program margin. The programming of the PPB for a given sector or sector group can be verified by writing a Sector Protection Status command to the device. 15.10 Program Suspend/Program Resume Commands The Program Suspend command allows the system to interrupt an embedded programming operation so that data can read from any non-suspended sector. When the Program Suspend command is written during a programming process, the device halts the programming operation within tPSL (program suspend latency) and updates the status bits. Addresses are "don't-cares" when writing the Program Suspend command. After the programming operation has been suspended, the system can read array data from any non-suspended sector. The Program Suspend command may also be issued during a programming operation while an erase is suspended. In this case, data may be read from any addresses not in Erase Suspend or Program Suspend. If a read is needed from the Secured Silicon Sector area, then user must use the proper command sequences to enter and exit this region. The system may also write the autoselect command sequence when the device is in Program Suspend mode. The device allows reading autoselect codes in the suspended sectors, since the codes are not stored in the memory array. When the device exits the autoselect mode, the device reverts to Program Suspend mode, and is ready for another valid operation. See "Autoselect Command Sequence" for more information. After the Program Resume command is written, the device reverts to programming. The system can determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard program operation. See "Write Operation Status" for more information. The system must write the Program Resume command (address bits are "don't care") to exit the Program Suspend mode and continue the programming operation. Further writes of the Program Resume command are ignored. Another Program Suspend command can be written after the device has resumed programming. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 39 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 15.11 Command Definitions Tables Table 15.1 contains the Memory Array Command Definitions. Table 15.1 Memory Array Command Definitions Cycles Bus Cycles (Notes 1-4) Addr RA XXX Data RD F0 (BA) 555 (BA) 555 (BA) 555 (BA) 555 555 SA (BA) 100 90 (BA) 000 90 90 90 A0 25 (BA) X01 X03 (SA) X02 PA SA 007F 227E (8) XX00 / XX01 PD WC PA PD WBL PD (BA) X0E (10) (BA) X0F (10) 001C Addr Data Addr Data Addr Data Addr Data Addr Data Command (Notes) Read (5) Reset (6) 1 1 Manufacturer ID Autoselect (Note 7) 4 555 AA 2AA 55 Device ID (10) Secured Silicon Sector Factory Protect (8) Sector Group Protect Verify(9) 6 4 4 4 6 1 3 6 6 1 1 1 2 3 2 2 1 2 555 555 555 555 555 SA 555 555 555 BA BA 55 XX 555 XX XX XX XXX AA AA AAA AA AA 29 AA AA AA B0 30 98 A0 AA A0 80 98 90 2AA 2AA 2AA 2AA 2AA 55 55 55 55 55 Program Write to Buffer Program Buffer to Flash Write to Buffer Abort Reset Chip Erase Sector Erase Program/Erase Suspend (11) Program/Erase Resume (12) CFI Query (13) Accelerated Program (15) Unlock Bypass Entry (15) Unlock Bypass Program (15) Unlock Bypass Erase (15) Unlock Bypass CFI (13)(15) Unlock Bypass Reset (15) 2AA 2AA 2AA 55 55 55 555 555 555 F0 80 80 555 555 AA AA 2AA 2AA 55 55 555 SA 10 30 PA 2AA PA XX PD 55 PD 10 555 20 XXX 00 Legend BA = Address of bank switching to autoselect mode, bypass mode, or erase operation. Determined by PL064 Amax:A19, PL032: Amax:A18. PA = Program Address (Amax:A0). Addresses latch on falling edge of WE# or CE# pulse, whichever happens later. PD = Program Data (DQ15:DQ0) written to location PA. Data latches on rising edge of WE# or CE# pulse, whichever happens first. RA = Read Address (Amax:A0). RD = Read Data (DQ15:DQ0) from location RA. SA = Sector Address (Amax:A12) for verifying (in autoselect mode) or erasing. WC = Word Count is the number of write buffer location to load minus 1. WBL = Write Buffer Location. The address must be within the same write buffer page as PA. X = Don't care Notes 1. 2. 3. 4. 5. 6. See Table 9.1 for description of bus operations. All values are in hexadecimal. Shaded cells in table denote read cycles. All other cycles are write operations. During unlock and command cycles, when lower address bits are 555 or 2AAh as shown in table, address bits higher than A11 (except where BA is required) and data bits higher than DQ7 are don't cares. No unlock or command cycles required when bank is reading array data. The Reset command is required to return to reading array (or to erase-suspend-read mode if previously in Erase This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 40 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 7. 8. 9. 10. 11. 12. 13. 14. 15. Suspend) when bank is in autoselect mode, or if DQ5 goes high (while bank is providing status information). Fourth cycle of autoselect command sequence is a read cycle. System must provide bank address to obtain manufacturer ID or device ID information. See Autoselect Command Sequence for more information. The data is DQ6=1 for customer locked . The data is 00h for an unprotected sector group and 01h for a protected sector group. Device ID must be read across cycles 4, 5, and 6. PL064 (X0Eh = 2202h, X0Fh = 2201h), PL032 (X0Eh = 220Ah, X0Fh = 2201h). System may read and program in non-erasing sectors, or enter autoselect mode, when in Program/Erase Suspend mode. Program/ Erase Suspend command is valid only during a sector erase operation, and requires bank address. Program/Erase Resume command is valid only during Erase Suspend mode, and requires bank address. Command is valid when device is ready to read array data or when device is in autoselect mode. WP#/ACC must be at VID during the entire operation of command. Unlock Bypass Entry command is required prior to any Unlock Bypass operation. Unlock Bypass Reset command is required to return to the reading array. Table 15.2 Sector Protection Command Definitions Cycles Bus Cycles (Notes 1-4) Addr XXX 555 555 555 555 555 555 555 555 555 Data Addr Data Addr Data Addr Data Addr Data Addr Data Addr Data F0 AA AA AA AA AA AA AA AA AA 2AA 2AA 2AA 2AA 2AA 2AA 2AA 2AA 2AA 55 55 55 55 55 55 55 55 55 555 555 555 555 555 555 555 555 555 88 90 60 60 60 90 60 78 58 SA RD (1) XX OW OW (SA) WP (SA) WP WP 00 68 48 68 RD (0) 60 (SA) 40 (SA) WP RD (0) OW OW (SA) WP 48 RD (0) 48 (SA) WP RD (0) OW RD (0) Command (Notes) Reset Secured Silicon Sector Entry (16) Secured Silicon Sector Exit (16) Secured Silicon Protection Bit Program (Notes 5, 6) Secured Silicon Protection Bit Status PPB Program (Notes 5, 6, 11) PPB Status All PPB Erase (Notes 5, 6, 13, 14) PPB Lock Bit Set PPB Lock Bit Status (15) 1 3 4 6 5 6 4 6 3 4 Legend OW = Address (A7:A0) is (00011010) PD[3:0] = Password Data (1 of 4 portions) PPB = Persistent Protection Bit RD(0) = Read Data DQ0 for protection indicator bit. RD(1) = Read Data DQ1 for PPB Lock status. SA = Sector Address where security command applies. Address bits Amax:A12 uniquely select any sector. SL = Persistent Protection Mode Lock Address (A7:A0) is (00010010) WP = PPB Address (A7:A0) is (00000010) X = Don't care SPMLB = Persistent Protection Mode Locking Bit Notes 1. 2. 3. 4. 5. 6. 7. 8. See Table 9.1 for description of bus operations. All values are in hexadecimal. Shaded cells in table denote read cycles. All other cycles are write operations. During unlock and command cycles, when lower address bits are 555 or 2AAh as shown in table, address bits higher than A11 (except where BA is required) and data bits higher than DQ7 are don't cares. The reset command returns device to reading array. Cycle 4 programs the addressed locking bit. Cycles 5 and 6 validate bit has been fully programmed when DQ0 = 1. If DQ0 = 0 in cycle 6, program command must be issued and verified again. Data is latched on the rising edge of WE#. Entire command sequence must be entered for each portion of password. 41 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. Rev. D, Issue Date: 2008/03/27 EN29PL064/032 9. 10. 11. 12. 13. 14. 15. 16. Command sequence returns FFh if PPMLB is set. The password is written over four consecutive cycles, at addresses 0-3. A 2 s timeout is required between any two portions of password. A 100 s timeout is required between cycles 4 and 5. A 1.2 ms timeout is required between cycles 4 and 5. Cycle 4 erases all PPBs. Cycles 5 and 6 validate bits have been fully erased when DQ0 = 0. If DQ0 = 1 in cycle 6, erase command must be issued and verified again. Before issuing erase command, all PPBs should be programmed to prevent PPB overerasure. DQ1 = 1 if PPB locked, 0 if unlocked. Once the Secured Silicon Sector Entry Command sequence has been entered, the standard array cannot be accessed until the Exit SecSi Sector command has been entered or the device has been reset. 16. Write Operation Status The device provides several bits to determine the status of a program or erase operation: DQ2, DQ3, DQ5, DQ6, and DQ7. Table 16.1 and the following subsections describe the function of these bits. DQ7 and DQ6 each offer a method for determining whether a program or erase operation is complete or in progress. The device also provides a hardware-based output signal, RY/BY#, to determine whether an Embedded Program or Erase operation is in progress or has been completed. 16.1 DQ7: Data# Polling The Data# Polling bit, DQ7, indicates to the host system whether an Embedded Program or Erase algorithm is in progress or completed, or whether a bank is in Erase Suspend. Data# Polling is valid after the rising edge of the final WE# pulse in the command sequence. During the Embedded Program algorithm, the device outputs on DQ7 the complement of the datum programmed to DQ7. This DQ7 status also applies to programming during Erase Suspend. When the Embedded Program algorithm is complete, the device outputs the datum programmed to DQ7. The system must provide the program address to read valid status information on DQ7. If a program address falls within a protected sector, Data# Polling on DQ7 is active for approximately 1 s, then that bank returns to the read mode. During the Embedded Erase algorithm, Data# Polling produces a "0" on DQ7. When the Embedded Erase algorithm is complete, or if the bank enters the Erase Suspend mode, Data# Polling produces a "1" on DQ7. The system must provide an address within any of the sectors selected for erasure to read valid status information on DQ7. After an erase command sequence is written, if all sectors selected for erasing are protected, Data# Polling on DQ7 is active for approximately 400 s, then the bank returns to the read mode. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. However, if the system reads DQ7 at an address within a protected sector, the status may not be valid. When the system detects DQ7 has changed from the complement to true data, it can read valid data at DQ15-DQ0 on the following read cycles. Just prior to the completion of an Embedded Program or Erase operation, DQ7 may change asynchronously with DQ15-DQ0 while Output Enable (OE#) is asserted low. That is, the device may change from providing status information to valid data on DQ7. Depending on when the system samples the DQ7 output, it may read the status or valid data. Even if the device has completed the program or erase operation and DQ7 has valid data, the data outputs on DQ15-DQ0 may be still invalid. Valid data on DQ15-DQ0 will appear on successive read cycles. Table 16.1 shows the outputs for Data# Polling on DQ7. Figure 16.1 shows the Data# Polling algorithm. Figure 20.10 shows the Data# Polling timing diagram. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 42 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Figure 16.1 Data# Polling Algorithm Notes 1. 2. VA = Valid address for programming. During a sector erase operation, a valid address is any sector address within the sector being erased. During chip erase, a valid address is any non-protected sector address. DQ7 should be rechecked even if DQ5 = "1" because DQ7 may change simultaneously with DQ5. 16.2 RY/BY#: Ready/Busy# The RY/BY# is a dedicated, open-drain output pin which indicates whether an Embedded Algorithm is in progress or complete. The RY/BY# status is valid after the rising edge of the final WE# pulse in the command sequence. Since RY/BY# is an open-drain output, several RY/BY# pins can be tied together in parallel with a pull-up resistor to VCC. If the output is low (Busy), the device is actively erasing or programming. (This includes programming in the Erase Suspend mode.) If the output is high (Ready), the device is in the read mode, the standby mode, or one of the banks is in the erase-suspend-read mode. Table 16.1 shows the outputs for RY/BY#. 16.3 DQ6: Toggle Bit I Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm is in progress or complete, or whether the device has entered the Erase Suspend mode. Toggle Bit I may be read at any address, and is valid after the rising edge of the final WE# pulse in the command sequence (prior to the program or erase operation), and during the sector erase time-out. During an Embedded Program or Erase algorithm operation, successive read cycles to any address cause DQ6 to toggle. The system may use either OE# or CE# to control the read cycles. When the operation is complete, DQ6 stops toggling. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 43 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 After an erase command sequence is written, if all sectors selected for erasing are protected, DQ6 toggles for approximately 400 s, then returns to reading array data. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or is erase-suspended. When the device is actively erasing (that is, the Embedded Erase algorithm is in progress), DQ6 toggles. When the device enters the Erase Suspend mode, DQ6 stops toggling. However, the system must also use DQ2 to determine which sectors are erasing or erasesuspended. Alternatively, the system can use DQ7 (see the DQ7: Data# Polling ). If a program address falls within a protected sector, DQ6 toggles for approximately 1 s after the program command sequence is written, then returns to reading array data. DQ6 also toggles during the erase-suspend-program mode, and stops toggling once the Embedded Program algorithm is complete. Table 16.1 shows the outputs for Toggle Bit I on DQ6. Figure 16.2 shows the toggle bit algorithm. Figure 20.11 shows the toggle bit timing diagrams. Figure 20.12 shows the differences between DQ2 and DQ6 in graphical form. See also the DQ2: Toggle Bit II . Figure 16.2 Toggle Bit Algorithm Note: The system should recheck the toggle bit even if DQ5 = "1" because the toggle bit may stop toggling as DQ5 changes to "1." See the DQ6: Toggle Bit I and DQ2: Toggle Bit II for more information. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 44 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 16.4 DQ2: Toggle Bit II The "Toggle Bit II" on DQ2, when used with DQ6, indicates whether a particular sector is actively erasing (that is, the Embedded Erase algorithm is in progress), or whether that sector is erasesuspended. Toggle Bit II is valid after the rising edge of the final WE# pulse in the command sequence. DQ2 toggles when the system reads at addresses within those sectors that have been selected for erasure. (The system may use either OE# or CE# to control the read cycles.) But DQ2 cannot distinguish whether the sector is actively erasing or is erase-suspended. DQ6, by comparison, indicates whether the device is actively erasing, or is in Erase Suspend, but cannot distinguish which sectors are selected for erasure. Thus, both status bits are required for sector and mode information. Refer to Table 16.1 to compare outputs for DQ2 and DQ6. Figure 16.2 shows the toggle bit algorithm in flowchart form, and the DQ2: Toggle Bit II explains the algorithm. See also the DQ6: Toggle Bit I . Figure 20.11 shows the toggle bit timing diagram. Figure 20.12 shows the differences between DQ2 and DQ6 in graphical form. 16.5 Reading Toggle Bits DQ6/DQ2 Refer to Figure 16.2 for the following discussion. Whenever the system initially begins reading toggle bit status, it must read DQ7-DQ0 at least twice in a row to determine whether a toggle bit is toggling. Typically, the system would note and store the value of the toggle bit after the first read. After the second read, the system would compare the new value of the toggle bit with the first. If the toggle bit is not toggling, the device has completed the program or erase operation. The system can read array data on DQ7-DQ0 on the following read cycle. However, if after the initial two read cycles, the system determines that the toggle bit is still toggling, the system also should note whether the value of DQ5 is high (see the section on DQ5). If it is, the system should then determine again whether the toggle bit is toggling, since the toggle bit may have stopped toggling just as DQ5 went high. If the toggle bit is no longer toggling, the device has successfully completed the program or erase operation. If it is still toggling, the device did not completed the operation successfully, and the system must write the reset command to return to reading array data. The remaining scenario is that the system initially determines that the toggle bit is toggling and DQ5 has not gone high. The system may continue to monitor the toggle bit and DQ5 through successive read cycles, determining the status as described in the previous paragraph. Alternatively, it may choose to perform other system tasks. In this case, the system must start at the beginning of the algorithm when it returns to determine the status of the operation. 16.6 DQ5: Exceeded Timing Limits DQ5 indicates whether the program or erase time has exceeded a specified internal pulse count limit. Under these conditions DQ5 produces a "1," indicating that the program or erase cycle was not successfully completed. The device may output a "1" on DQ5 if the system tries to program a "1" to a location that was previously programmed to "0." Only an erase operation can change a "0" back to a "1." Under this condition, the device halts the operation, and when the timing limit has been exceeded, DQ5 produces a "1." Under both these conditions, the system must write the reset command to return to the read mode (or to the erase-suspend-read mode if a bank was previously in the erase-suspend-program mode). 16.7 DQ3: Sector Erase Timer After writing a sector erase command sequence, the system may read DQ3 to determine whether or not erasure has begun. (The sector erase timer does not apply to the chip erase command.). When the time-out period is complete, DQ3 switches from a "0" to a "1." See also the Sector Erase Command Sequence. After the sector erase command is written, the system should read the status of DQ7 (Data# Polling) or DQ6 (Toggle Bit I) to ensure that the device has accepted the command sequence, and then read This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 45 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 DQ3. If DQ3 is "1," the Embedded Erase algorithm has begun; all further commands (except Erase Suspend) are ignored until the erase operation is complete. If DQ3 is "0," the device will accept additional sector erase commands. To ensure the command has been accepted, the system software should check the status of DQ3 prior to and following each subsequent sector erase command. If DQ3 is high on the second status check, the last command might not have been accepted. Table 16.1 shows the status of DQ3 relative to the other status bits. Table 16.1 Write Operation Status Status Embedded Program Standard Algorithm Mode Embedded Erase Algorithm Erase SuspendRead Erase Suspended Sector Non-Erase Suspended Sector DQ7 (Note 2) DQ7# 0 1 DQ5 (Note 1) 0 0 0 DQ2 (Note 2) No toggle Toggle Toggle DQ6 Toggle Toggle No toggle DQ3 N/A 1 N/A RY/BY# 0 0 1 Erase Suspend Mode Data DQ7# Data Toggle Data 0 Data N/A Data N/A 1 0 1 Erase-Suspend -Program Program Suspend Mode (Note 3) Reading within Program Suspended Sector Reading within Non-program Suspended Sector Invalid Invalid Invalid Invalid Invalid (Not Allowed) (Not Allowed) (Not Allowed) (Not Allowed) (Not Allowed) Data Data Data Data Data 1 Notes: 1. 2. 3. DQ5 switches to `1' when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits. Refer to DQ5: Exceeded Timing Limits for more information. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details. When reading write operation status bits, the system must always provide the bank address where the Embedded Algorithm is in progress. The device outputs array data if the system addresses a non-busy bank. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 46 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 17. Absolute Maximum Ratings Storage Temperature Plastic Packages Ambient Temperature with Power Applied Voltage with Respect to Ground VCC (Note 1) A9, OE#, and RESET# (Note 2) WP#/ACC (Note 2) All other pins (Note 1) Output Short Circuit Current (Note 3) -0.5 V to +4.0 V -0.5 V to +12.0 V -0.5 V to +10.5 V -0.5 V to VCC +0.5 V 200 mA -65C to +150C -65C to +125C Notes: 1. Minimum DC voltage on input or I/O pins is -0.5 V. During voltage transitions, input or I/O pins may overshoot VSS to -2.0 V for periods of up to 20 ns. Maximum DC voltage on input or I/O pins is VCC +0.5 V. During voltage transitions, input or I/O pins may overshoot to VCC +2.0 V for periods up to 20 ns. See Figure 17.1 Minimum DC input voltage on pins A9, OE#, RESET#, and WP#/ACC is -0.5 V. During voltage transitions, A9, OE#, WP#/ACC, and RESET# may overshoot VSS to -2.0 V for periods of up to 20 ns. See Figure 17.1 . Maximum DC input voltage on pin A9, OE#, and RESET# is +12.5 V which may overshoot to +14.0 V for periods up to 20 ns. Maximum DC input voltage on WP#/ACC is +9.5 V which may overshoot to +12.0 V for periods up to 20 ns. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second. Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability 2. 3. 4. Figure 17.1 Maximum Overshoot Waveforms This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 47 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 18. Operating Ranges Operating ranges define those limits between which the functionality of the device is guaranteed. Industrial (I) Devices Ambient Temperature (TA) ................-40C to +85C Wireless (W) Devices Ambient Temperature (TA) ................-25C to +85C Supply Voltages VCC ...................................................2.7-3.6 V This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 48 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 19. DC Characteristics Table 19.1 CMOS Compatible Parameter Parameter Description (notes) ILI ILIT ILR ILO ICC1 ICC2 ICC3 ICC4 ICC5 ICC6 ICC7 ICC8 ICC9 VIL VIH VHH VID VOL VOH VLKO Input Load Current A9, OE#, RESET# Input Load Current Reset Leakage Current Output Leakage Current VCC Active Read Current (1, 2) VCC Active Write Current (2, 3) VCC Standby Current (2) VCC Reset Current (2) Automatic Sleep Mode (Notes 2, 4) VCC Active Read-While-Program Current (1, 2) VCC Active Read-While-Erase Current (1, 2) VCC Active Program-While-EraseSuspended Current (2, 5) VCC Active Page Read Current (2) Input Low Voltage Input High Voltage Voltage for ACC Program Acceleration Voltage for Autoselect and Temporary Sector Unprotect Output Low Voltage Output High Voltage Low VCC Lock-Out Voltage (5) Test Conditions VIN = VSS to VCC, VCC = VCC max VCC = VCC max; VID= 11.5 V VCC = VCC max; VID= 11.5 V VOUT = VSS to VCC, OE# = VIH VCC = VCC max OE# = VIH, VCC = VCC max OE# = VIH, WE# = VIL CE#, RESET#, WP#/ACC = VIO 0.3 V RESET# = VSS 0.3 V VIH = VIO 0.3 V; VIL = VSS 0.3 V OE# = VIH, OE# = VIH, OE# = VIH OE# = VIH, 4 word Page Read VIO = 2.7-3.6 V VIO = 2.7-3.6 V VCC = 3.0 V 10% VCC = 3.0 V 10% IOL = 2.0 mA, VCC = VCC min, VIO = 2.7-3.6 V IOH = -100 A, VIO = VCC min 5 MHz 10 MHz 5 MHz 10 MHz 5 MHz 10 MHz Min Typ Max 1.0 35 35 1.0 Unit A A A A mA mA A A A mA mA mA mA V V V V V V 20 45 15 0.2 0.2 0.2 21 46 21 46 17 10 -0.5 2 8.5 10.5 30 55 25 5 5 5 45 70 45 70 25 15 0.8 VCC+0.3 9.5 11.5 0.4 VCC0.2V 2.3 2.5 V Notes 1. 2. 3. 4. 5. The ICC current listed is typically less than 5 mA/MHz, with OE# at VIH. Maximum ICC specifications are tested with VCC = VCCmax. ICC active while Embedded Erase or Embedded Program is in progress. Automatic sleep mode enables the low power mode when addresses remain stable for tACC + 30 ns. Typical sleep mode current is 2 A. Not 100% tested. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 49 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 20. AC Characteristic 20.1 Test Conditions Figure 20.1 Test Setups 3.3 V 2.7 k Device under Test CL 6.2 k Note: Diodes are IN3064 or equivalent Table 20.1 Test Specifications Test Conditions Output Load Output Load Capacitance, CL (including jig capacitance) Input Rise and Fall Times Input Pulse Levels Input timing measurement reference levels Output timing measurement reference levels All Speeds 1 TTL gate 30 5 0.0-3.0 Vcc/2 Vcc/2 pF ns V V V Unit This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 50 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 20.2 Switching Waveforms Table 20.2 Key To Switching Waveforms Figure 20.2 Input Waveforms and Measurement Levels 20.3 VCC Ramp Rate All DC characteristics are specified for a VCC ramp rate > 1V/100 s. If the VCC ramp rate is < 1V/100 s, a hardware reset required.+ This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 51 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 20.4 Read Operations Speed Options Description (Notes) Read Cycle Time (1) Address to Output Delay Chip Enable to Output Delay Page Access Time Output Enable to Output Delay Chip Enable to Output High Z (3) Output Enable to Output High Z (1, 3) Output Hold Time From Addresses, CE# or OE#, Whichever Occurs First (3) Output Enable Hold Time (1) Read Toggle and Data# Polling Test Setup CE#, OE# = VIL OE# = VIL Min Max Max Max Max Max Max Min Min Min 70 70 70 70 25 25 16 16 5 0 10 Unit ns ns ns ns ns ns ns ns ns ns Table 20.3 Read-Only Operations Parameter JEDEC tAVAV tAVQV tELQV tGLQV tEHQZ tGHQZ tAXQX Std. tRC tACC tCE tPACC tOE tDF tDF tOH tOEH Notes 1. 2. 3. Not 100% tested. See Figure 20.1 and Table 20.1 for test specifications Measurements performed by placing a 50 ohm termination on the data pin with a bias of VCC /2. The time from OE# high to the data bus driven to VCC /2 is taken as tDF. Figure 20.3 Read Operation Timings Figure 20.4 Page Read Operation Timings This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 52 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 20.5 Reset Table 20.4 Hardware Reset (RESET#) Parameter JEDEC Std All Speed Options Max Max Min Min Min Min 20 500 500 50 20 0 Description RESET# Pin Low (During Embedded Algorithms) to Read Mode tReady (See Note) RESET# Pin Low (NOT During Embedded Algorithms) to Read Mode tReady (See Note) tRP RESET# Pulse Width tRH Reset High Time Before Read (See Note) tRPD RESET# Low to Standby Mode tRB RY/BY# Recovery Time Unit s ns ns ns s ns Note Not 100% tested. Figure 20.5 Reset Timings This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 53 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 20.6 Erase/Program Operations Table 20.5 Erase and Program Operations Parameter JEDEC tAVAV tAVWL tWLAX tDVWH tWHDX tGHWL tELWL tWHEH tWLWH tWHDL Std tWC tAS tASO tAH tAHT tDS tDH Write Cycle Time (Note 1) Address Setup Time Address Setup Time to OE# low during toggle bit polling Address Hold Time Address Hold Time From CE# or OE# high during toggle bit polling Speed Options (ns) Description Min Min Min Min Min Min Min Min Min Min Min Min Min Min Typ Typ Typ Min Min Max Min Program Suspend Latency Erase Suspend Latency Max Max 70 70 0 15 35 0 30 0 10 0 0 0 35 25 0 6 4 0.5 50 0 90 35 35 35 ns ns ns ns ns ns ns ns ns ns ns ns ns s s sec s ns ns ns s s Unit Data Setup Time Data Hold Time tOEPH Output Enable High during toggle bit polling tGHWL Read Recovery Time Before Write (OE# High to WE# Low) tCS tCH tWP tWPH tSR/W CE# Setup Time CE# Hold Time Write Pulse Width Write Pulse Width High Latency Between Read and Write Operations tWHWH 1 tWHW H1 Programming Operation (Note 2) tWHWH 1 tWHW H1 Accelerated Programming Operation (Note 2) tWHWH 2 tWHW H2 Sector Erase Operation (Note 2) tVCS tRB tBUSY tPSL tESL VCC Setup Time (Note 1) Write Recovery Time from RY/BY# Program/Erase Valid to RY/BY# Delay Notes: 1. 2. Not 100% tested. See Table 21.4 for more information. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 54 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 20.7 Timing Diagrams Figure 20.6 Program Operation Timings Notes 1. PA = program address, PD = program data, DOUT is the true data at the program address Figure 20.7 Accelerated Program Timing Diagram This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 55 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Figure 20.8 Chip/Sector Erase Operation Timings Notes 1. SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see Write Operation Status ) Figure 20.9 Back-to-back Read/Write Cycle Timings This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 56 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Figure 20.10 Data# Polling Timings (During Embedded Algorithms) Note VA = Valid address. The illustration shows first status cycle after command sequence, last status read cycle, and array data read cycle Figure 20.11 Toggle Bit Timings (During Embedded Algorithms) Notes 1. VA = Valid address; not required for DQ6. The illustration shows first two status cycle after command sequence, last status read cycle, and array data read cycle This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 57 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Figure 20.12 DQ2 vs. DQ6 Note DQ2 toggles only when read at an address within an erase-suspended sector. The system may use OE# or CE# to toggle DQ2 and DQ6. 21. Protect/Unprotect Table 21.1 Temporary Sector Unprotect Parameter JEDEC Std tVIDR tVHH tRSP tRRB Description VID Rise and Fall Time (See Note) VHH Rise and Fall Time (See Note) RESET# Setup Time for Temporary Sector Unprotect RESET# Hold Time from RY/BY# High for Temporary Sector Unprotect Min Min Min Min All Speed Options 500 250 4 4 ns ns s s Unit Note Not 100% tested Figure 21.1 Temporary Sector Unprotect Timing Diagram This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 58 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Figure 21.2 Sector/Sector Block Protect and Unprotect Timing Diagram Notes 1. For sector protect, A6 = 0, A1 = 1, A0 = 0. For sector unprotect, A6 = 1, A1 = 1, A0 = 0. 21.1 Controlled Erase Operations Table 21.2 Alternate CE# Controlled Erase and Program Operations Parameter JEDEC tAVAV tAVWL tELAX tDVEH tEHDX tGHEL tWLEL tEHWH tELEH tEHEL Std tWC tAS tAH tDS tDH tGHEL tWS tWH tCP tCPH Description (Notes) Write Cycle Time (Note 1) Address Setup Time Address Hold Time Data Setup Time Data Hold Time Read Recovery Time Before Write (OE# High to WE# Low) WE# Setup Time WE# Hold Time CE# Pulse Width CE# Pulse Width High Min Min Min Min Min Min Min Min Min Min Typ Typ Typ Speed Options 70 70 0 35 30 0 0 0 0 35 25 6 4 0.5 Unit ns ns ns ns ns ns ns ns ns ns s s sec tWHWH1 tWHWH1 Programming Operation (Note 2) tWHWH1 tWHWH1 Accelerated Programming Operation (Note 2) tWHWH2 tWHWH2 Sector Erase Operation (Note 2) Notes 1. 2. Not 100% tested. See Erase And Programming Performance for more information. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 59 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Figure 21.3 Alternate CE# Controlled Write (Erase/Program) Operation Timings 555 for program PA for program Notes 1. 2. 3. Figure indicates last two bus cycles of a program or erase operation. PA = program address, SA = sector address, PD = program data. DQ7# is the complement of the data written to the device. DOUT is the data written to the device This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 60 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Table 21.4 Erase And Programming Performance Parameter Sector Erase Time Chip Erase Time Word Program Time Accelerated Word Program Time Chip Program Time (Note 3) PL064 PL032 PL064 PL032 Typ (Note 1) Max (Note 2) 0.5 2 71 39 6 4 25.2 12.6 113.6 62.4 100 60 50.4 25.2 Unit sec sec sec s s sec sec Comments Excludes 00h programming prior to erasure (Note 4) Excludes system level overhead (Note 5) Notes 1. 2. 3. 4. 5. 6. Typical program and erase times assume the following conditions: 25C, 3.0 V VCC, 100,000 cycles. Additionally, programming typical assume checkerboard pattern. All values are subject to change. Under worst case conditions of 90C, VCC = 2.7 V, 1,000,000 cycles. All values are subject to change. The typical chip programming time is considerably less than the maximum chip programming time listed, since most bytes program faster than the maximum program times listed. In the pre-programming step of the Embedded Erase algorithm, all bytes are programmed to 00h before erasure. System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program command. See Table 15.1 for further information on command definitions. The device has a minimum erase and program cycle endurance of 100,000 cycles. 22. 48-PIN TSOP PACKAGE CAPACITANCE Parameter Symbol CBIN B Parameter Description Input Capacitance Output Capacitance Control Pin Capacitance Test Setup VBIN = 0 B Typ Max Unit 6 8.5 7.5 7.5 12 9 pF pF pF CBOUT B VBOUT = 0 B CBIN2 B VBIN = 0 B Note: Test conditions are Temperature = 25C and f = 1.0 MHz 23. BGA Pin Capacitance Parameter Symbol CIN COUT CIN2 CIN3 Parameter Description Input Capacitance Output Capacitance Control Pin Capacitance WP#/ACC Pin Capacitance Test Setup VIN = 0 VOUT = 0 VIN = 0 VIN = 0 Typ 6.3 7 5.5 11 Max 7 8 8 12 Unit pF pF pF pF Notes 1. 2. Sampled, not 100% tested. Test conditions TA = 25C, f = 1.0 MHz. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 61 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 24. Physical Dimensions Figure 24.1 TSOP 48-pin 12mm x 20mm This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 62 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 63 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Figure 24.2 48-ball TFBGA package outline (PL032) SYMBOL A A1 A2 D E D1 E1 e DIMENSION IN MM MIN. --0.23 0.84 7.90 5.90 ------NOR --0.29 0.91 8.00 6.00 5.60 4.00 0.80 MAX 1.30 ----8.10 6.10 ------0.45 b 0.35 0.40 Note : 1. Coplanarity: 0.1 mm This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 64 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Figure 24.3 56-ball Fine-Pitch Ball Grid Array (FBGA) 7 x 9 mm Package SYMBOL A A1 A2 D E D1 E1 e b DIMENSION IN MM MIN. --0.25 0.71 6.90 8.90 ------0.35 NOR --0.30 0.76 7.00 9.00 5.60 5.60 0.80 0.40 65 MAX 1.20 0.35 0.81 7.10 9.10 ------0.45 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. Rev. D, Issue Date: 2008/03/27 EN29PL064/032 Revisions List Revision No A B C Description Date Voltage Method) in page 21 Initial Release 2007/9/19 Update the 48 Ball package thickness from 1.31mm to 1.2mm in 2007/12/21 page 64 Correct the Manufacturer ID at Table 9.7 Autoselect Codes (High 2008/1/3 D 1. Change the customer-lockable words from 128 words to 64 words in page 1, 21, 26 and 27 2. Change the page access times from 20ns to 25ns in page 1, 2, 5 and 52. 3. Remove 65ns speed grade in page 1, 2, 5, 52, 54 and 59. 4. Change VID from 11.5-12.5V to 10.5-11.5V in page 11and 49. 2008/3/27 5. Update the CFI table in page 29 and 30. 6. Remove the 48-ball FBGA Connection Diagrams for PL064 in page 8 7. Correct the 48 Ball package thickness from 1.2mm to 1.3mm in page 64 8. Add the 56 Ball FBGA Connection Diagrams and Physical Dimensions in page 9 and page 65 This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. 66 (c)2004 Eon Silicon Solution, Inc., www.essi.com.tw Rev. D, Issue Date: 2008/03/27 |
Price & Availability of EN29PL064-70BI
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |